2-1 FUNDAMENTALS OF AUTOMOTIVE BATTERIES
INTRODUCTION
In the first lesson you learned that electricity can be produced magnetically. Electricity is also produced chemically by means of a battery.
Batteries used in automotive vehicles supply electricity for cranking the engine, igniting the fuel mixture in the cylinders, and operating most accessories. In fact, cars as they are now designed could not operate without batteries. Understanding the batteries and knowing how to keep them in good condition are vital parts of good automotive maintenance. Present-day cars would be quite helpless and of no use without the electricity furnished by a good battery that is properly connected.
We, as mechanics, must know a great deal about batteries to keep them in good working order. Automotive batteries need daily attention from the operator plus some frequent maintenance performed by the operator and the mechanic, as well as special attention under certain conditions. To do your part, you will need knowledge of batteries and the procedures involved in their maintenance.
A battery is nothing more than two unlike conductors immersed in a special solution called electrolyte.
You can make a battery in a few minutes if you have a lemon, a paper clip, and a piece of uninsulated copper wire. Here is how it is done:
Straighten out the paper clip and cut the copper wire so it is the same length as the paper clip. Stick both the clip and the wire deep into the lemon so they are close together but not touching. Now, if you touch the free ends of the wire and paper clip to your tongue, you will experience a slight tingle and a metallic taste.
The tingle and the metallic taste are due to electrons passing through the saliva on your tongue. The lemon juice is the electrolyte solution; the steel paper clip and the copper wire are the two unlike conductors. Action of acid in the juice combining with the conductors causes an excess of electrons to build up on one conductor. When you touched your tongue to the conductors, you closed the circuit and electrons began to flow.
Almost everyone is familiar with the common flashlight battery (dry-cell battery).
The battery consists of a zinc cup-like container that is sealed at the top. A carbon rod is set in the middle of, and insulated from, the container. The rod extends out the top with its exposed tip covered by a metal cap. The cup is filled with a mixture of materials that make up a paste-like electrolyte. The carbon rod and the zinc case are the unlike conductors, with the case containing the negative charge and the rod the positive.
A good flashlight battery has an electrical charge of 1½ volts. As the battery is used, the voltage gets lower. Finally, it reaches a point where it no longer furnishes enough electrical power to do the job right and must be replaced. The battery is then said to be discharged or run-down.
CONSTRUCTION
Storage batteries used in automotive vehicles are the lead-acid type and are often referred to as wet-cell batteries. They operate on the same principle as our lemon battery and the flashlight battery, using an electrolyte and two unlike conductors to store electrical energy in chemical form. To satisfy the high current and dependability requirements of automotive vehicles, the construction of the lead-acid storage battery is complex. The parts of the battery are described below.

FIGURE 15. PLATE CONSTRUCTION.
The conductors that are immersed in electrolyte are two kinds of PLATES known as positive and negative plates. Both the positive and negative plates have a grid framework made of a stiff lead alloy for strength. The active material is applied to the grids in paste form and allowed to dry and harden like cement, then it is put through a special forming process. When finished, the active material of the positive plates is brown lead peroxide, the negative plates, gray spongy lead.

FIGURE 16. CELL GROUP CONSTRUCTION.
Each plate has a lug on one top corner. Several plates are combined into positive and negative GROUPS by welding these lugs to a plate strap, which is also made of lead. A negative group of plates has negative plates only and a positive group positive plates only. The plate strap on each group of plates contains a terminal post, which forms an outside electrical connection.
A positive and a negative plate group, along with several insulators called SEPARATORS, are put together to form an ELEMENT. The thin separators are inserted between the positive and negative plates to prevent them from touching and short-circuiting the battery internally. They are generally made of a material, such as wood, rubber, or glass, and contain many small holes so the liquid electrolyte can pass through.
When the assembled element, consisting of the positive and negative plate groups and separators, is immersed in electrolyte, it becomes a CELL. The voltage of a charged cell as measured with an open circuit is about 2.1 volts, regardless of the size of the cell. For practical purposes we generally just say that the voltage of the cell is 2 volts. In order to obtain more than 2 volts from a battery, several cells are used and connected in series (negative to positive). For example, a 6-volt battery will contain three cells and a 12-volt battery six cells. The cell terminals are connected by welding them to connector straps.
All the cells of a battery are placed in a one-piece container or case that is divided into compartments. Each compartment is the container for one cell. The bottom of each cell compartment generally has raised ribs for the element to rest on. The area between the ribs serves as sediment space. During use, the active material on the plates gradually sheds and falls into the sediment space. The entire container is made of hard rubber or some other insulating material that is resistant to acid and to mechanical shock.

FIGURE 17. CROSS-SECTION OF A TYPICAL STORAGE BATTERY.
The top of each cell is fitted with a cell cover made from a material, such as hard rubber like the container. Some cell covers are made so the straps connecting the cell terminals are exposed. On others, the connecting straps are covered and only two terminal posts are exposed. Regardless of the type of cover used, each cell cover is fitted with a vent plug, which may be removed to inspect the cell or to add water.
To seal the battery after the cell cover is installed, the space between the edges of the cell covers and the container is filled with an acid-resistant compound. Some form of seal is also used where the terminal post extends through the cover.
The vent plug (filler cap) contains a small hole to permit the escape of gas formed in the cell. A series of baffles may be built into the plug so the gas must pass around them in leaving the cell. The baffles prevent electrolyte from splashing out through the venthole. Also, any mist from the electrolyte is collected here and returned to the cell.
Batteries designed for use in tactical vehicles are waterproof. The vent plugs will not allow water to enter the cells during fording operations but will still permit gases to escape. This is done by a pressure vent valve in the vent plug. The valve closes to external water pressure and opens to release internal gas pressure.
Electrical power comes from the battery through two TERMINAL POSTS. The posts are tapered, and the positive terminal is slightly larger than the negative terminal. The cable clamps are also made in two sizes, to reduce the chances of connecting a battery in reverse.
The cells of the battery are filled with a mixture of sulfuric acid and distilled water, the electrolyte. Electrical energy is produced by the chemical action of the sulfuric acid on the plates. The electrolyte also serves as a carrier for the electric current inside the battery. The electrolyte of a fully charged battery contains about 38 percent sulfuric acid by weight (about 27 percent by volume).
OPERATION

FIGURE 18. BATTERY DISCHARGE/CHARGE CYCLE.
Now that you are familiar with the construction of the automotive battery, let's consider the chemical reaction that takes place in the battery.
A battery cell is said to be fully charged when the electrolyte is full strength. The active material of the negative plates consists of spongy lead, and the active material of the positive plates consists of lead peroxide.
When a load is connected to the battery, electrons flow from the negative plates to the positive plates. The battery is said to be "discharging." Chemical changes take place inside the battery during discharging:
As the current flows, atoms of the sulfuric acid leave the electrolyte and enter the battery plates. This decreases the amount of acid that is in the electrolyte, making the mixture weaker.
As you recall, atoms from all elements are different, and the nature of all materials is determined by the atoms they contain. Therefore, the atoms of sulfuric acid mixing with the battery plates will change the nature of the plates. The spongy lead of the negative plates turns into lead sulfate; the lead peroxide of the positive plates also turns into lead sulfate.
If current flow continues, the electrolyte will get weaker and weaker until it is almost all water. At the same time, the negative and positive plates will be gradually turning into lead sulfate so that they are becoming alike (both lead sulfate). Finally, the battery reaches a point where it will no longer supply enough voltage to cause the current flow, and the battery is then said to be discharged.
This chemical reaction in the automotive battery can be reversed and the discharged battery returned to a charged state. This is done by supplying DC from an external power source, such as a DC generator, and running it through the battery opposite the direction it travels when the battery is discharging. This causes the atoms from the acid to return to the electrolyte making the electrolyte stronger. As the acid atoms leave the battery plates, the plates change back to their original nature--spongy lead and lead peroxide.
As a battery is charged, some of the water in the electrolyte is broken down and passes off in the form of gas. If charging is continued after the battery is fully charged, the amount of gas given off increases and the battery overheats. This is called overcharging and can damage the battery. The gas given off by a battery during the charging process is explosive and can be easily ignited by a spark.
Repeated charging and discharging slowly wears out the battery. It causes the lead peroxide to fall off the positive plates into the sediment space in the bottom of the container. The sediment may build up high enough to cause a short circuit between the negative and positive plates, but normally the cell will be worn out before the sediment reaches the bottom of the plates.
SPECIFIC GRAVITY
The strength of the battery electrolyte is determined by comparing its weight to that of an equal volume of pure water. Pure water has a specific gravity (weight) of 1.000. Let's suppose that we compare 1 gallon of water to 1 gallon of a second substance and find that the second substance weighs 2½ times more than the water. The second substance is said to have a specific gravity of 2.500 or 2½ times that of water. Pure sulfuric acid has a specific gravity of 1.835.
Since electrolyte is a mixture of sulfuric acid and water, the specific gravity of electrolyte will be more than the 1.000 of the water but less than the 1.835 of the acid. The mixture that is generally placed in batteries has a specific gravity of 1.280, and by volume it contains 73-percent water and 27-percent sulfuric acid.
Often the specific gravity of the electrolyte is simply referred to as the gravity of the battery. Also, it is customary to omit the decimal point and refer to a specific gravity of 1.280 as "twelve eighty," 1.200 as "twelve hundred," and so forth. Variations of gravity in the third decimal place are referred to as points. For example, 1.284 is four points higher than 1.280.
VOLTAGE AND CAPACITY
There is a distinct difference between the voltage and capacity of a battery.
This difference can be easily seen by picturing two cans of water, one small and the other large, placed on top of a building. If the water from both cans is poured over the side of the building, the pressure or force it has when it hits the ground will depend on the distance it falls. The distance is the same regardless of which can the water comes from. This is comparable to battery voltage since voltage is electrical pressure. Each cell of an automotive battery has slightly over 2 volts. This is true regardless of the size of the cell.
Now, let's imagine that one of the cans contains one gallon of water and the other can five gallons. You can see that if the water is poured from both cans at the same rate, water can be poured five times as long from the large can. From another viewpoint, if we empty both cans in the same length of time, the large can pours five times as much water in the same amount of time. This is comparable to battery capacity. More battery capacity is obtained by giving the electrolyte more plate surface to contact. This can be done by making the plates larger or by using a larger number of plates.
Battery voltage and capacity are different, and each one has a definite effect upon the other as well as the circuit.
We know that the battery must supply the correct amount of voltage to push just the right amount of current through the circuits. Too much voltage will cause too much current to flow, which will burn out bulbs, and so forth. If battery voltage is too low, the current flow will not be enough and the circuits will not operate right.
When a load is connected to the battery, the current flow will cause the battery voltage to drop due to internal resistance in the battery cells. The amount of voltage drop under a load is affected by the following:
The larger the capacity of the battery, the less the voltage drops.
As the battery's state of charge gets lower, the more the voltage drops.
The greater the current flow, the greater the voltage drop.
As the battery wears out, active material drops off the plates, which reduces the battery's capacity and causes a larger voltage drop under the load.
As outdoor temperature drops, the electrolyte gets thicker, which slows down its action and causes a larger voltage drop during cold weather.
BATTERY RATINGS
The current required by the electrical systems of two vehicles are often different, even though they require the same voltage. For instance, both the ¼- and 5-ton trucks have 24-volt electrical systems, but the batteries used in the ¼-ton truck will not supply enough current to satisfactorily crank the large engine of the 5-ton truck.
We can tell which battery has a larger capacity or current-producing capability by physical size, just like judging a bigger can will hold more water, but that is not an exact measurement.
The amount of water the cans will hold is measured in pints, quarts, or gallons. Battery capacity is measured in ampere-hours, which is the number of amperes the battery will deliver multiplied by the number of hours the battery will deliver it. For example, suppose a battery will deliver 5 amperes for 20 hours, then 5 amperes multiplied by 20 hours equals 100 ampere-hours.
If the ampere-hour rating is based on nothing more than the method described above, the rating would change if the rate of discharge changed. Suppose that we increase the load on the battery from 5 to 10 amperes. The battery would produce the 10 amperes for a period less than 20 hours, so its rating would be less than 100 ampere-hours. As you can see, some standard procedure must be used to rate the ampere-hours so that the ratings will mean the same in all cases.
The capacity of automotive batteries is rated by a standard procedure known as the 20-hour rating. This rating gives the number of ampere-hours a battery will deliver if it is discharged at a uniform rate for 20 hours, at a temperature of 80°, and with a battery voltage of 1.75 volts per cell at the end of the 20-hour period.
Two sizes of batteries, type 2HN and 6TN, are commonly used in tactical wheeled vehicles. Both types are 12-volt batteries. The smaller 2HN battery is rated 45 ampere-hours; the larger 6TN battery is rated 100 ampere-hours.
TESTING AUTOMOTIVE BATTERIES
Through use and age, the capacity of a battery decreases. This is due to some of the active material dropping off the plates and the build-up of a hard coating of sulfate on the plates. Because of this, testing the gravity of the battery with a hydrometer may not always reveal the true condition of the battery. The electrolyte may be strong enough, but the battery capacity may be reduced to a point where the available current supply is too small. This condition can be detected by making a high-rate discharge test of the battery.
Do not perform a high-rate discharge test when the specific gravity of the electrolyte is 1.225 or less or if the variation of specific gravity between cells is more than 25 points. After charging, the battery should be allowed to sit for several hours before a high-rate discharge test.
High-rate discharge testing instruments vary a great deal. Always perform a high-rate discharge test according to instructions for the test instrument you are using. In use, the test instrument draws a high current from the battery and the battery voltage is read on a voltmeter during the discharge. The correct amount of voltage will vary depending on the test instrument used.
If a high-rate discharge tester is not available, batteries can still be tested if they are installed in the vehicle. This is done by using an ordinary voltmeter to measure the battery voltage while cranking the engine. The starter motor serves as the high-current load. Refer to -20 technical manual for the vehicle for the exact procedures and correct voltage readings.
CONNECTING BATTERIES IN SERIES AND SERIES-PARALLEL
As you know, tactical vehicles have 24-volt electrical systems, twice the voltage supplied by each 12-volt battery used. In addition, some of the vehicles demand more current for cranking than the 100 ampere-hour battery can supply. To satisfy the increased voltage and current requirements, more than one battery is used in each vehicle. To satisfy the specific requirements of different vehicles, the batteries are connected in series or series-parallel.
In order to increase voltage, the batteries are connected in series. Recall that in a series circuit the current has only one path to follow; therefore, the same current will flow through all batteries when they are connected in series. A series connection of two batteries is made by connecting the negative terminal post of one battery to the positive terminal post of another battery. Batteries connected in series should have the same ampere-hour rating. A voltage source equal to the sum of both batteries is then available at the two remaining terminal posts. The ampere-hour rating of batteries connected in series is the same as the smallest battery by itself. For instance, some trucks use two 6TN batteries which are rated at 12 volts and 100 ampere-hours each. The batteries are connected in series to furnish a power source of 24 volts and 100 ampere-hours.
In order to increase the ampere-hour rating, the batteries are connected in parallel. In a parallel circuit the current has more than one path to follow. Batteries connected in parallel must have the same voltage rating. To connect two batteries in this manner, the positive terminal posts of both batteries are connected together and then the negative terminals of the batteries are connected. Each battery will now furnish half the current flowing in the load so their ampere-hour ratings will be added together, but the voltage will be the same as one battery alone. The parallel connection of batteries when used in tactical wheeled vehicles is combined with the series connection and is known as the series-parallel connection.

FIGURE 19. BATTERY INSTALLATION CONFIGURATIONS.
Batteries are connected in series-parallel to increase both the voltage and the ampere-hour rating. To demonstrate how we make use of the series-parallel connection, let's say that we have a vehicle that requires a 24-volt, 200-ampere-hour power source.
We will use four 12-volt, 100-ampere-hour batteries. The batteries are first set apart in pairs. In each pair, the batteries are connected in series so they will provide 24 volts and 100 ampere-hours per pair. Then, the two pairs are connected in parallel to increase the capacity rating to 200 ampere-hours.