LESSON 1
PRINCIPLES AND METHODS
TEXT ASSIGNMENT: Attached Memorandum
LESSON OBJECTIVES
Upon completion of this lesson n Principles and Methods, you should be able to accomplish the following in the indicated topic areas:
1. Line Conventions. Interpret the established line conventions and symbols used on engineering drawings.
2. Projections. Explain the principles of orthographic projections, perspective drawings, and isometric projections.
3. Orthographic Drawings. Describe the fundamentals of orthographic drawings, and how they are used to construct objects.
4. Special Views. List and describe the various special views used to supplement an orthographic drawing, including sections and auxiliaries.
5. Reproduction of Construction Prints. List and explain the different methods used to reproduce construction prints.
6. Construction Print Format. Describe the format of a construction print.
7. Fundamentals of Interpretation. Interpret simple orthographic drawings by relating them to the isometric views of the objects.
ATTACHED MEMORANDUM
Section I Meaning of Lines
1-1. DRAWINGS
a. A picture is worth a thousand words. Man has used pictures as a means of communication for many years. It would be almost impossible for an engineer or an inventor to describe the size and shape of a simple object without a drawing of some kind. For example, if an engineer designed a simple object such as that shown in the engineer's sketch in figure 1-1 it would be difficult to convey his idea to the person who is to fabricate the object without a drawing to show the shape, size, and location of the holes. A working drawing of the object is also shown in figure 1-1.

Figure 1-1. Engineer's sketch compared to working drawing.
b. Drawing or sketching is the universal language used by engineers, technicians, and skilled craftsmen. Whether this drawing is made freehand or by the use of drawing instruments (mechanical drawing), it is needed to convey all the necessary information to the individual who will fabricate and assemble the object whether it be a building, ship, aircraft, or mechanical device.
1-2. LINE CONVENTIONS
In order to include all the necessary information on a drawing in a meaningful manner, different types and weights of lines are used to represent the features of the object. The meaning of a line with certain characteristics has been standardized, and will be the same on any drawing. These line conventions must be understood in order to read drawings. The line conventions most often encountered in construction prints are described below and shown in figure 1-2. Application of these line conventions are demonstrated in figure 1-3.
Figure 1-2. Line Conventions.
Figure 1-3. Applications of line conventions.
a. Visible Lines. A heavyweight unbroken line is used for the primary feature of a drawing. For drawings of objects, this line convention represents the edges, the intersection of two surfaces, or the surface limit that is visible from the viewing angle of the drawing. This line is often called the outline.
b. Hidden Lines. A medium weight line of evenly spaced short dashes represents an edge, the intersection of two surfaces, or the surface limit which is not visible from the viewing angle of the drawing.
c. Center Lines. A thin (light) line composed of alternate long and short dashes of consistent length is called a center line. It is used to signify the center of a circle or arc and to divide an object into equal or symmetrical parts.
d. Dimension Lines. A solid continuous line terminating in arrowheads at each end. Dimension lines are broken only to permit writing in dimension. On construction drawings the dimension lines are unbroken. The points of the arrowheads touch the extension lines which mark the limits of the dimension. The dimension is expressed in feet and inches on architectural drawings and in feet and decimal fraction of a foot on engineering drawings.
e. Extension Lines. Extension line is a thin (light) unbroken line that is used to indicate the extent of the dimension lines. The extension line extends the visible lines of an object when it is not convenient to draw a dimension line directly between the visible lines. There is always a small space between the extension line and the visible line.
f. Leaders. A leader is a thin (light) line terminated with an arrowhead that is used to indicate the part or feature to which a number, note, or other information refers.
g. Phantom Lines. A medium weight line made of long dashes broken by two short dashes is called a phantom line and indicates one of three things: the relative position of an absent part, an alternative position of a part, or repeated detail which is not drawn.
h. Stitch Lines. A medium line made of short dashes evenly spaced and labeled used to indicate stitching or sewing.
i. Break Lines. A thin (light) line interrupted by a z-shaped symbol. The break line indicates that the object has been shortened to save space on the drawing. The true length is indicated by the dimension specified. The short break line convention varies with shape and material, figure 1-4, and indicates that part of the object has been cut away to show section detail or hidden features.
Figure 1-4. Short break conventions.
j. Cutting Plane Lines. A pair of short, heavy lines with arrowheads projected at 90 degrees indicates the cutting plane when a drawing includes a section view. Letters (AA, BB, etc. ) are usually placed at the arrowheads to identify the section view. The arrowheads show the viewing direction of the section view. Where necessary, the section lines may be connected by a line of short, heavy dashes indicating the exact path of the cutting plane.
k. Section Lines. When a drawing includes a section, the surface or surfaces which are in the cutting plane are indicated by section lines. When the object sectioned is all one material, the section lines are usually closely spaced parallel lines of medium thickness. Where different materials are involved, different section conventions are used to distinguish between them.
REVIEW QUESTIONS
Section II. Projections, Views, and Dimensions
1-3. INTRODUCTION
In learning to read a construction print, you must develop the ability to visualize the object, figure 1-5. This is done by learning to properly interpret the various types of lines, dimensions, sections, details, symbols, and other media that are used to describe the object or parts of an object on a construction print.
Figure 1-5. Visualizing from a print.
1-4. PROJECTIONS
An object can be viewed and therefore drawn from an infinite number of positions. Some views are easier to draw and interpret than others. It is common to present an object on a drawing as an orthographic projection or as a pictorial drawing. In an orthographic projection, the object is presented as if it were viewed through a transparent drawing plan from an infinite distance (fig 1-6). An orthographic projection is made by projecting each point on the object perpendicular to the drawing plane. A pictorial drawing, such as the perspective projection in figure 1-6, presents the object as it would appear to the eye.
Figure 1-6. Orthographic versus perspective projection.
a. Orthographic Projection. Almost all drawings intended for production or construction are drawn by orthographic projection.
(1) The major advantage of an orthographic projection is that it shows every part of an object that is parallel to the drawing plane in true relative size and position.
(2) The numbers of views to be used in projecting a drawing are governed by the complexity of the shape of the drawing. Complex objects are normally drawn showing six views; that is both ends, front, top, rear, and bottom. Figure 1-7 shows an object placed in a transparent box. The projections of the object on the sides of the box are the views seen by looking straight at the object through each side. If the outlines are scribed on each surface and the box opened and laid flat, the result is a six-view, orthographic projection drawing. It should be noted that the rear view may appear in any one of four positions (to the right of the right side view or left of the left side view, above the top or below the bottom view).
Figure 1-7. Third angle orthographic projection.
(3) As a general rule, you will find that most drawings will be presented in three views. For a simple object, three views are adequate to completely describe the object when dimensions are added (fig 1-8).
Figure 1-8. Three-view drawing.
Occasionally, you will see two-view drawings, particularly cylindrical objects. The most common three-view drawing arrangement shows the front, top, and right side view of an object.
(4) In a three-view drawing, the front view shows the most characteristic feature of the object. Note in figure 1-8 that the right side or end view is projected to the right of the front. Also notice that all the horizontal outlines of the front view are extended horizontally to make up the side view and all the vertical outlines of the front view are extended vertically to make up the top view. By studying the drawing you should obtain the following information about the object: the shape of the object, its overall length (2 1/8 inches), its width (1 1/2 inches), and its height (1 3/8 inches). It is notched 1 1/8 inches from the right side and 7/8 inch from the bottom. After having studied each view of the object, you should be able to visualize the object as it appears in figure 1-9. If a hole is drilled in the notched portion of the object, the drawing would appear as in figure 1-10. The position of the hole is indicated by hidden lines in the front and side views and as a circle in the top view. The location of the center of the drilled hole is indicated by a center line.
Figure 1-9. Interpretation of a three-view drawing.
Figure 1-10. Hidden lines in a three-view drawing.
b. Pictorial Drawings. It is easier to visualize an object if its features can be shown in a single view. Where it is necessary for the drawing to show the appearance of an object with more than one side visible in a single view, pictorial drawings are used. Three types of pictorial drawings may be encountered: projections, oblique drawings, and perspective drawings.
(1) Projections. The principle of pictorial projections is the same as orthographic projection, but the object is rotated and tilted so that more than one face is projected on the drawing plane as shown in figure 1-11. Since the faces of the object are not parallel to the drawing plane, lines are foreshortened and do not appear in true length. If each object plane forms a different angle with the drawing plane, the amount of foreshortening is different along the axis of the drawing. This is called a trimetric projection (fig 1-11) and three different scales must be used. If the object is rotated so that two planes form the same angle with the drawing plane, the amount of foreshortening will be the same along two axes. This is called a dimetric projection (fig 1-11) since only two scales are used. If the object is tilted so that all three planes form the same angle with drawing plane, the scale will be the same along all three axes. This is called an isometric projection (fig 1-11) , and is the most common type in technical work. All lines parallel with one of the three principal axes are foreshortened by the same amount (to about 81 percent of true length) on an isometric projection. In isometric drawing (fig 1-11) the common practice is to enlarge the scale factor so that lines appear in true length. Remember, however, that this applies only to lines which are parallel to one of the axes.
Figure 1-11. Pictorial projections of a cube.
(2) Oblique drawings. In oblique drawings (fig 1-12) the front face of the object is drawn in orthographic form, full scale. One or more sides are then added at an angle to the front face, either full scale, or foreshortened. Any angle and scale may be used.
Figure 1-12. Oblique drawings of a cube.
(a) Cavalier drawing. An oblique drawing in which the receding or oblique lines are drawn full-scale at 45 degrees is called a cavalier drawing (fig 1-12) . The result does not create a realistic appearance, but allows the use of one scale for the entire drawing.
(b) Cabinet drawing. A cabinet drawing is an oblique drawing which uses half-scale measurements on the oblique sides (fig 1-12). These drawings are commonly drawn with the oblique lines at 30 degrees or 45 degrees to the front plane. The name comes from the fact that it is often used for drawings of cabinet work.
(3) Perspective drawings. The most realistic pictorial is the perspective drawing. In this type of drawing, the receding lines converge at a vanishing point on a horizon, just as they appear to do when you look at an object. The perspective may be two-point (two vanishing points) as illustrated in figure 1-13 or one-point (one vanishing point) as illustrated in figure 1-14. In a one-point perspective, the front face appears as if you were looking at it head-on. The viewing angle may be changed by the selection of different positions relative to the horizon (fig 1-14). Perspective drawings are more difficult to draw than projections or oblique drawings, because the scale changes continuously along the receding lines; for this reason, they are not practical for construction drawings.
Figure 1-13. Two-point perspective drawing.
Figure 1-14. One-point perspective drawings.
1-5. SPECIAL VIEWS
When complex objects are involved, three-view drawings are often not sufficient to convey all the necessary details. Special views are added to provide additional information. The special views which may be encountered are auxiliary and rotation views, sections, phantom views, developments, and exploded views.
a. Auxiliary Views. If a feature of an object is in a plane which is not parallel to one of the drawing planes, it will not appear in true size or shape in any of the three normal views. The sloping surface of the object in figure 1-15, for example, appears in both the top and right side views but is foreshortened in both. In this case, an auxiliary projection is added. The auxiliary view is obtained by projecting lines to a drawing plane which is parallel to the slanted face. The auxiliary view is normally placed alongside a view which shows the true length of the edge of the slanted surface as shown in figure 1-16. In this case, the auxiliary view is related to the front view. If the feature to be covered in an auxiliary view is not in a plane Figure 1-16. Auxiliary view arrangement, perpendicular to one of the normal orthographic drawing planes, or if there is not enough room in the normal position, the auxiliary view will be placed somewhere else on the drawing. In this case; the auxiliary view will usually be labeled as "view A" (or B, C, etc) with an arrow pointing to the face. Auxiliary views do not usually show the entire object as seen from the auxiliary view angle; only the surface parallel to the auxiliary drawing plane is covered. Figure 1-17 shows an auxiliary view compared with a right side view of the same object. Note that the circles appear as ellipses in the right side view, and the distances between centers are foreshortened. The auxiliary view only shows the slanted face of the object, the holes appear in true shape, and the distances in true length.
Figure 1-15. Auxiliary projection principle.
Figure 1-16. Auxiliary view arrangement.
Figure 1-17. Auxiliary and side views compared.
b. Rotation. Occasionally, if no confusion will result from the practice, a separate auxiliary view is omitted and a side or top view is provided, drawn as if the object was bent to bring the slanted surface parallel to the drawing plane (fig 1-18). This is called a rotation, and the fact that it has been done will be indicated in some manner on the drawing. In figure 1-18, for example, the fact that one view is higher than the other, plus the curvature of the upper center line shows immediately that the right hand view is a rotation.
Figure 1-18. Rotation.
c. Sections. Section views are used to give a clear view of the interior or hidden features of the object which normally cannot be clearly observed in conventional outside views. A section view is obtained by cutting away part of an object to show the shape and construction at the cutting plane. The most common position of the cutting plane is through the longest dimension, or main longitudinal axis and parallel to the front view as shown in figure 1-19. The cutting plane may be drawn parallel to any plane of projection if it shows the required features of the object. When section views are drawn, the part that is cut by the cutting plane is marked with close spaced, parallel (section) lines. The section lines indicate the surfaces which were created by the cutting plane and which do not exist on the uncut object. When two or more parts are cut in one view, a different slant or style of section line is used for each part. All rules of projection apply, but hidden lines complete understanding of the view. Notice how the cutting plane is shown on a drawing as Illustrated in [1] figure 1-19. The cutting plane in [2] illustrates where the imaginary cut is made. The object as it would look if were cut in half is shown in [3]. The section view as it would appear on a drawing is shown in [4].
Figure 1-19. Action of the cutting plane.
(1) Full-sections. When the cutting plane is a single continuous plane passing entirely through the object, the resulting view is called a full-section view [1] (fig 1-20). The cutting plane is usually taken straight through on the main axis or center line.
Figure 1-20. Full and half-sectional views.
(2) Half-sections. The cutting plane will not always be taken completely through the object. [2] Figure 1-20 shows a half section. The cutting plane passes only half way through the object. This is common practice for symmetrical objects. In the case illustrated, the top half, if sectioned, would be identical to the bottom half, providing no additional information. The half-section permits both the internal and external features to be shown and their relationship to one another.
(3) Offset section. A section view which has the cutting plane changing direction backward and forward (zig-zag), so as to pass through features that are important to show, is known as an offset section. The offset cutting plane in figure 1-21 is arranged so that the hole on the right side will be shown in section. The sectional view is the front view, and the top views show the offset cutting plane line. Notice that there is no line on the section view at the point where the cutting plane goes straight back.
Figure 1-21. Offset Section.
(4) Revolved section. To eliminate drawing extra views of rolled shapes, ribs, and similar forms, a revolved section is used. It is a drawing within a drawing, and it clearly describes the object's shape at a certain cross-section station or point. The sectional view of the rib in figure 1-22 has been revolved so that you can look at it head-on.
Figure 1-22. Revolved section.
(5) Removed section. Removed sections are normally used to illustrate particular parts of an object (fig 1-23). They are drawn like the removed section, except that they are placed at one side to bring out important details. They are often drawn to a larger scale than the view on which they are indicated.
Figure 1-23. Removed Section.
(6) Broken-out section. A broken-out section is a partial section used on an exterior view to show some interior detail without drawing a complete full or half section. The limit of the broken-out section is indicated with an irregular break line. In figure 1-24, the inside of the fitting is better illustrated because of the broken-out section.
Figure 1-24. Broken-out section.
(7) Alined section. Look at the front view of the handwheel in figure 1-25 and notice the cutting plane line AA. When a true sectional view might be misleading, parts such as ribs or spokes are drawn as if they are rotated into or out of the cutting plane. Notice that the spokes in the section at A-A are not sectioned. In some cases, though not in this figure, if the spokes were sectioned, the first impression would be that the wheel had a solid web rather than spokes.
Figure 1-25. Alined section.
d. Phantom Views. Phantom views are used to indicate the alternate position and path of motion of parts, repeated details, or the relative position of an absent part. Figure 1-26 shows the alternate position of a part as a phantom view (the part of the left side).
Figure 1-26. Phantom view.
e. Development. A development is a drawing which is used for objects which are made from flat materials by bending and joining, such as ducts. The development (also called a stretch-out or pattern drawing) shows the shape of the material before it is formed into the assembled object (fig 1-27).
Figure 1-27. Development of a truncated pentagonal prism.
f. Exploded Views. Exploded views are used to illustrate the assembly or disassembly of a unit which has several removable parts. It is basically a pictorial view of each of the parts to the same scale, with the parts arranged in a relationship which corresponds to their relationship when assembled (fig 1-28).
Figure 1-28. Exploded view.
1-6. DIMENSIONS
a. The item you will be most concerned with when reading prints is the dimensions. As previously stated, dimensions on architectural drawings are usually given in feet, inches, and fractions of an inch. Engineering drawings often give dimensions in feet and decimal fractions of a foot. Metric dimensions are used on drawings of European origin, most drawings related to optical equipment, and a growing percentage of American machine drawings. During construction, you should use measuring instruments calibrated in the same system as used on the construction prints to eliminate the chance of error in conversion.
b. The placement of dimensions on a drawing is not arbitrary. They are placed to indicate which dimensions are specified in the design of the object. Measurements for construction should always be made from the points indicated by the dimension lines on the print.
c. Figure 1-29 is a typical dimensioned drawing of a bearing journal and can be used to illustrate the proper way to make measurements from the points indicated by the dimension lines on the print. Let's consider the measurements required to locate the two mounting holes. If you were using this print and were drilling the mounting holes, you should notice in the front view that the center of the right hole is located 1 inch from the center of the large hole. The top view shows that the center of the left hole is 2 inches from the center of the right hole. This method of making measurements introduces two possible sources of error. There is some tolerance in the location of the right hand mounting hole, and some tolerance in the measurement you make to locate the left-hand mounting hole. Any other system of measurements will introduce additional sources of error. For example, it can be determined from the dimensions that the mounting holes are located 1/4 inch from the edges and the centers could be located in this manner. However, this introduces three sources for error. There is some tolerance in the width of the journal (the 2 1/2-inch dimension) and some tolerance in the location of the centers of the two mounting holes. These three sources for errors could accumulate and result in a significant error in the distance between the two mounting holes. This distance is critical to the mounting of the journal. It is also possible to locate the center of one hole 1/4 inch from the edge and then measure the 2 inches to the center of the other hole. This procedure also introduces three possible sources of error. There is some tolerance in the width of the journal, in the location of one hole, and in the measurement made to locate the second hole. This method reduces the sources of error in the distance between the mounting holes. However, it does introduce possible error in the location of the main hole. It may not be centered between the mounting holes. These examples emphasize the importance of the location of the dimensions when making the measurements in construction.
Figure 1-29. Typical working drawing.
REVIEW QUESTIONS
Section III. Types of Prints
1-7. CLASSES OF DRAWINGS
Drawings are normally classified as original drawings, intermediate or reproducibles, or prints. The original drawing is the one produced by the draftsman. An intermediate is a copy of the original which is used to make prints. An intermediate is used to avoid the risk of damaging the original or because the original is not suitable for the type of reproduction process used for the making of prints. Prints may also be made directly from the original without using an intermediate drawing. A print is a working copy used on the job.
1-8. PRODUCTION PROCESSES
There are many processes used to make prints from originals or intermediates. They can be classified as either negative or positive contact processes or optical processes. Contact processes require a transparent or translucent original. Optical copies can be made from opaque originals. Contact processes are normally used in construction work. Optical copies are usually more expensive and introduce more distortion.
a. Negative Contact Processes.
(1) Blueprints. A blueprint is made by placing a tracing (transparent or translucent original) in contact with a sensitized paper and exposing the paper through the tracing. When the paper is developed, the unexposed portions where the light is blocked by lines on the original remain white, while the exposed portions turn dark blue. This produces a print with white lines on a blue background. Blueprints, in general, have better contrast than other commonly used processes of comparable cost but the wet developing process causes some distortion and marking the prints is difficult.
(2) Brownprints. The brownprint process (often called Van Dyke) is similar to the blueprint process except that the paper is transparent and exposed areas turn brown when developed. This yields transparent lines on a brown background. Brownprints are frequently used as intermediates producing a print which has blue lines on a white background and called a white-print.
b. Positive Contact Processes.
(1) Ozalid prints. The ozalid process is a contact process like blueprinting but the unexposed areas of the sensitized paper turn blue when developed in ammonia vapor, producing blue lines on a white background. Ozalid prints are also called blueline prints. Papers are also available which yield black lines (called blackline prints) . The development in this process is dry, causing less distortion than the blueprint process, but the contrast is not usually as good.
Note: Machines are available which produce ozalid-process prints but which project and reduce the image optically instead of contact-printing. Prints produced by this process will usually be marked "Reduced Size Print -Do Not Scale. "
(2) Brownline prints. Brownline prints have the same function in the ozalid process as the brownprints do in the blueprint process. They produce brown lines on a transparent background and are often used as an intermediate for making blueline prints. Brownline prints are often called sepia intermediates.
(3) Special materials. Materials are available for use with the ozalid process which produce a large variety of results, including many colored lines on white paper or colored lines on a clear plastic background.
c. Optical Processes.
(1) Electrostatic. An electrostatic copier (Xerox machine for example) projects an image of the original on paper and then causes an electrostatic charge to be deposited where the image of a line occurs. A black powdered "ink" is then applied to the paper and adheres where the electrostatic charge occurs. The image is then fused to the paper. This process produces a dark gray image on a white background. The amount of distortion depends on the type and quality of the optical system which projects the image on the copy paper.
(2) Photostat. The photostat process is a photographic process which uses a special camera and film. The film is opaque paper instead of transparent film as in ordinary photography. Since the negative is opaque and cannot be viewed from the back, the camera is designed to produce an erect image instead of reversed image as with ordinary cameras. The photostat process produces white lines on a black background (negative photostat) which can then be rephotographed to produce a black image on a white background (positive photostat) . The image can be enlarged or reduced in the photostat process, usually to 1/2 or 2 times original size in each stage.
(3) Microfilm. For economy of storage space and for insurance against destruction of the original, many drawings are photographically copied on microfilm. When a drawing is no longer in frequent use, the original is often disposed of and only the microfilm copy is retained. Equipment is available for viewing microfilm copies (similar to a slide viewer) and for making prints directly from microfilm copies. Since the image must go through the original optical reduction, development of the microfilm, enlargement, and the final print process, the chance of distortion is high.
1-9. HANDLING PRINTS
a. A complete drawing represents too much time and effort to be treated casually. It is a valuable record, and must be preserved with care. If an original drawing were to be used on the job and passed from man to man, it would soon become worn and too dirty to read. For this reason, working drawings used on the job are almost always reproductions of original drawings.
b. A little time spent in carefully folding and filing prints at the start will prevent a lot of inconvenience later on. The method of folding depends on the facilities available for storage. Some filing equipment commonly used is shown in figure 1-30. When manufactured filing equipment is not available in the field, storage facilities should be constructed. Prints should be folded so the drawing number is visible when the print is filed. If storage space is available to accommodate rolls, prints over 40 inches long are usually rolled instead of folded. Original drawings or intermediates used for contact process reproduction should never be folded; the creases will prevent close contact with the copy paper.
Figure 1-30. Print and drawing storage.
c. When using prints on the job, avoid long exposure to direct sunlight or the prints will fade. If it is necessary to mark a print, be neat and use a colored pencil. A red pencil is normally used to show additions and a yellow pencil is used to indicate deletions. After using a print, refold it carefully to avoid adding unnecessary creases.
REVIEW QUESTIONS
Section IV. Parts of a Print
1-10. DRAWING FORMATS
A drawing not only provides information about the size and shape of the object being represented but also provides information that enables the drawing to be identified, processed, and filed methodically. The systematic arrangement of the drawing sheet to provide a consistent location for this information is known as the format of a drawing. Sizes and formats for military drawings are arranged in accordance with certain standards.
a. Drawing Sizes. Military drawings are prepared in standard sizes, designated by letters. These sizes are listed in Table 1-1. Roll size drawings are normally prepared with an extra 4-inch margin for protection if possible without exceeding the 144-inch length limit. Complete details on military drawings may be found in MIL-STD-100A.
Table 1-1. Finished Format Sizes (Inches)
b. Title Block. A typical title block as illustrated in figure 1-31 shows the name and address of the preparing agency (A), the title of the drawing (B), the drafting record (C), authentication and date (D), the scale and specification number (E), and the drawing number and sheet number for multiple-sheet drawings (F).
Figure 1-31. Typical title block.
(1) Drawing number. Each drawing is identified by a drawing number, which appears in a number block. It may be shown in other places also; for example, near the top border line, in the upper corner, or on the reverse side at both ends so that it will be visible when a drawing is rolled up. The drawing number's purpose is to permit quick identification. If a drawing has more than one sheet, and each sheet has the same number. this information is included in the number block indicating the sheet number and the number of sheets in the series. When using construction drawings, always check to be sure that all necessary sheets are on hand.
Some multiple-sheet construction drawings have a "schedule of drawings" near the title block which lists the contents of each sheet.
(2) Scale. The scale block will indicate the scale on the drawing, either as a ratio (for example: 1/4 or 1: 4 meaning 1 inch on the drawing equals 4 inches on the object, or 12" = 1" meaning 12 inches on the drawing equals 1 inch on the object) or as a graphic scale as shown in figure 1-32. Where the same scale is not used on a parts of a drawing, the scale block may be marked "as noted" or left blank, and the scale noted underneath each part of the drawing. If graphic scales are used, several scales may be shown with numbers (fig 1-32) and the appropriate scale number alongside each part of the drawing. When reading drawings, always follow the dimensions specified on the drawing first, and use the scale on the drawing where no dimension is given. Do not measure with an architect's or engineer's scale directly on a print, since the print may be enlarged or reduced, or the paper may shrink during the copying process.
Figure 1-32. Graphic scales.
(3) Specification number. The specification number indicates the specification the draftsmen followed for assistance in interpreting the drawing.
e. Bill of Materials. A special block on the drawing may contain a list of the pieces of stock or standard parts necessary to construct the object on the drawing, and the quantity of each item required. This list may also be called a list of materials, schedule of equipment, or parts list. If several sheets are required for a particular object, the bill of materials may appear on a separate sheet(s).
d. Revision Block. Space is always left on a drawing to list revisions as they are made. The revision block will show the revision symbol, A, B, C, etc., consecutively as encountered, a brief description of the revision, the revision date and supervisor's approval, and sometimes the zone of the drawing in which the revision was made. If more than one copy of a drawing is available, the revision block should be checked to find the drawing with the latest revision.
e. Notes and Specifications. Notations explaining construction methods or specifying materials which are not indicated by symbols are called specifications. The notes may list allowable substitutions, special provisions for certain locations, additional reference materials, etc. The notes must always be read before beginning construction.
1-11. MILITARY DRAWINGS
Military drawings are classified as construction or production drawings, depending on the method of manufacture of the object or assembly represented on the drawing or set of drawings. The format of each type is arranged differently, although sheet and margin sizes are common to both.
a. Construction Drawings. Construction drawings are drawings developed to illustrate the design of structures or other constructions and the services, utilities, approaches, or any other features involved. Maps (except those with construction drawings), reports, sketches, presentation drawings, or renderings are not considered to be construction drawings within the meaning of this standard. The basic construction drawing format consists of the margin, the title block with its various subdivisions, the revision block, and the block containing the list of material. Figure 1-33 shows the layout and dimensions of the typical construction drawing format.
Figure 1-33. Format for a construction drawing.
b. Production Drawings. Production drawings describe equipment or articles that are suitable for production in quantity. The same basic information is normally included on a production drawing format as on a construction drawing format although the arrangement is different.
(1) Drawing number. A production drawing used by a government agency will frequently have both a manufacturer's drawing number and a government agency drawing number. Be sure to use the government agency number when dealing within the military supply system. In addition, a production drawing will often have a five-digit identification code for the manufacturer, for the government agency, or both. This number is called a Federal Supply Code (FSC) and permits locating the name and address of the manufacturer or agency in Handbook H 4-1 and -2 "Federal Supply Code for Manufacturers." The name and address of the manufacturer and cognizant government agency are usually included on the drawing, but the FSC is helpful because drawings are seldom revised for a change of address whereas the handbook is updated regularly. If the manufacturer's drawing number is used for any purpose, it should be prefixed by the FSC to indicate whose drawing number it is. It is also customary to add the latest revision letter to the number since the manufacturer may make additional revisions to his drawings after the item or drawing is supplied to the government. Revision D to drawing number 703145, by a manufacturer whose FSC is 90222, would be specified as 90222-703145D. When the drawings of different sizes are filed separately, the drawing size letter (table 1-1) is often shown in front of the number.
(2) Part number. In most production drawing systems, a part number is the same as the drawing number for the part except where more than one part is included on a drawing. In this case "dash numbers" are used. Each part covered by a drawing will have a dash number assigned and noted on the drawing. The part number is the drawing number followed by -1 or -2 etc., as applicable.
(3) Application or usage block. Most production drawings include a block which shows "next assembly" and "used on" information, as shown in figure 1-34. The "next assembly" column will list each assembly which includes the part. The "used on" column will list each end product which includes the part. For example, one pipe section might be used in several compressor assemblies, and in two or three different air-conditioning models. Sometimes the quantity required in each "next higher assembly" and in each end product is also listed.
Figure 1-34. Typical application or usage block.
REVIEW QUESTIONS
Section V. Interpretation of Drawings
1-12. INTRODUCTION
The objects used for illustrations thus far have been simple, and interpretation of the drawings nearly obvious. More complex or irregular drawing may require more effort to interpret. The principles introduced here along with the conventions peculiar to certain fields which are discussed in the following lessons will enable you to interpret any properly prepared drawing. The orthographic projection principles are fundamental to all fields and a thorough understanding of them is necessary if you are to read any type of physical prints.
1-13. FUNDAMENTALS OF INTERPRETATION
a. The fundamental step in interpreting a drawing is relating the different views. If you pick a point on a front view, the same point on the right side view will be directly to the right of it. Similarly, the same point on the top view will be directly above the point on the front view. These relationships are illustrated in [1] (figure 1-35) by the horizontal and vertical datum lines between the views. The same relationship exists between the top and right side views but is not obvious because they are not hinged together. If the outside edges of both views are extended horizontally or vertically until they cross, as in [2], figure 1-35, and a line is drawn connecting these points of intersection, the relationship can be seen. The line connecting the points of intersection will be at a 45-degree angle with the horizontal. Al other points in the view can be related by bending their project line at this 45-degree line. If the same point appears on three views, the three occurrences will be related as shown by point 1 in part [2] of figure 1-35. On complex drawings it is often helpful to draw this 4-degree line to be sure you are looking at the same point on all three views when interpreting the drawing.
Figure 1-35. Relationships in orthographic projection.
b. Figure 1-36 is a three-view drawing of an object, along with an isometric outline of a box with the same overall dimensions of the object. Trace off the isometric outline and points on a separate piece of paper and sketch in the details as you read the paragraph. This will help you to learn to visualize the object as you interpret a construction print. Looking at the right hand side of the front view, and the corresponding parts of the top and side views, interpretation of the part of the isometric diagram that has been completed should be apparent. Note the point marked "a" on the top view. From the projection indicated it must be the same as the point marked "a" on the right side view. Projecting these two points to the front view shows that the point marked "a" on all three views is the same point and is located at "a" on the isometric diagram. Next look at the line "ah" on the front view. Point "h" on the front view may correspond to point "g" or point "f" on the top view, but there is no line from "a" to "f" on the top view. Line "ah," therefore, must correspond to line "ag" and transferring points to the right side view, to line "ae." On the isometric view, this corresponds to the line from "a" to "n" which can now be drawn on the isometric view. Line "ab" on the front view must correspond to line "ac" on the top view, and to line "ad" on the right side view. This translates as a line from "a" to "q" on the isometric view. At this stage, it is evident that line "el" (right side view) is the same as line "hj" (front view) and a line has been drawn from "p" to "n" on the isometric view. Similarly, line "fc" (top) is the same as line "hb" (front) and a line has been drawn from "m" to "q" on the isometric view. Line "cg" (top) may correspond to either "hb" or "ja" (front) but not to "ha" which has already been established. If "cg" corresponds to "ja" it would also have to correspond to "la" in the right side view because point "a" has been established and "cg" does not project to "la" in the right side view. Therefore, "cg" corresponds to "hb" in the front view and to "ed" in the right side view. Line "cg" must correspond to a line from "n" to "q" on the isometric view. All that remains is to complete the isometric view with the only possible lines which do not contradict one or more of the three views; lines from "p" to "a" from "a" to "r" and from "r" to "q" produce an isometric which should look like figure 1-37 at the end of the section.
Figure 1-36. Exercises in interpretation.
Figure 1-37. Completed exercise.
REVIEW QUESTIONS
Self Test Exercise
Table of Contents
Downloadable Files