LESSON 1

 

GEODESY FOR THE LAYMAN

OVERVIEW

LESSON DESCRIPTION:

In this lesson, you will learn to identify the different datums and ellipsoids that encompass the earth.

TERMINAL LEARNING OBJECTIVE:

ACTION: You will learn to identify the different datums and ellipsoids.
CONDITION: You will be given the material contained in this lesson.
STANDARD: You will correctly answer all practice questions following this exercise.
REFERENCES: The material contained in this lesson was derived from FM 3-34.331.

INTRODUCTION

 

When Eratosthenes made his meridional arc measurement some twenty-two hundred years ago, the basic foundation for modern geodesy was established. Through the years, refinements have been made, necessary values of precision and accuracy have been determined, and a scientific attitude has evolved about solving the problem of size and shape. Geodesy is defined as the science of precise positioning of points on the earth's surface and the determination of the earth's exact size and shape. It also involves studying variations in the earth's gravity and how these variations apply to precise measurements of the earth. The geodesist's role is to put things on the surface of the earth in their exact places. In this lesson, you will learn how to perform this task.

PART A - FIGURES OF THE EARTH

 

1-1. Three Figures of the Earth. Before any type of measurement can take place, the surface on which we measure must be defined. Generally, we can assume the following three figures of the earth: topographic, mathematic, and geoidal.

a. Topographic. The surface most apparent is the actual topographic surface of the earth. This includes the mountains, valleys, and other continental and oceanic forms. The surveyor makes the actual measurements on these surfaces, but because of the irregularities of the land, this figure is not suitable for mathematical computations. This surface generally concerns the topographer and the hydrographer but interests the geodesist only with regard to the effect of the terrain features on gravity.

b. Mathematic. It is convenient to adopt a simple mathematical surface, resembling the actual earth, to permit simplified computations of positions on the earth's surface. We might select a simple sphere; however, the sphere is only a rough approximation of the true figure of the earth. We can and do use a spherical form to solve most astronomical problems and for navigation. The sphere is used to represent the earth because it is a simple surface that is easy to deal with mathematically.

c. Geoidal. The geoid is the equipotential surface within or around the earth where the plumb line is perpendicular to each point on the surface. The geoid is considered a mean-sea-level (MSL) surface that is extended continuously through the continents. The geoidal surface is irregular due to mass excesses and deficiencies with the earth. The figure of the earth is considered a sea-level surface that extends continuously through the continents. The geoid (which is obtained from observed deflections of the vertical) is the reference surface for astronomical observations and geodetic leveling. The geoidal surface is the reference system for orthometric heights.

1-2. Ellipsoid. Refer to Table 1-1 for ellipsoid data. The shape of the earth is more precisely represented mathematically by an ellipsoid of revolution, which is made by rotating an ellipse around its minor axis. The radius of the equator usually designates the size of an ellipsoid. The radius is called the semimajor axis (Figure 1-1). The shape of the ellipsoid is given by a flattening, which indicates how well an ellipsoid approaches the shape of a sphere. Figure 1-2 shows the flattening of various figures. The ellipsoid, which represents the earth very closely, approaches a sphere since it has a flattening of 1/300. An ellipse with such a small flattening is almost a perfect circle. Spheroid and ellipsoid of revolution are accurate terms; however, ellipsoid has become the more accepted term.

Table 1-1. Ellipsoid Data
Table 1-1.  Ellipsoid Data

 

Figure 1-1.  Components of an Ellipsoid
Figure 1-1. Components of an Ellipsoid

 

Figure 1-2.  Flattening Fraction
Figure 1-2. Flattening Fraction

 

a. Types of Ellipsoids. The two ellipsoids currently in use are named for the individuals who derived them. The differences between the two types are very small; however, there are a great number of ellipsoids actually in use. Generally, they describe or fit the portion of the earth where they are used.

(1) The international ellipsoid was developed by John F. Hayford in 1910 and adopted by the International Union of Geodesy and Geophysics (IUGG), which recommended it for international use.

(2) The new international ellipsoid was developed by William M. Kaula in 1964 and adopted by the IUGG, which recommended it for worldwide gravity surveys, updating of the World Geodetic System (WGS) and scientific survey requirements.

b. Axis of Rotation. The axis of rotation of an ellipsoid is always parallel to the axis of rotation of the earth. Ideally, the center of the ellipsoid should coincide with the earth's center of gravity. The bubble level on a surveyor's instrument shows only the general direction of the earth's center of gravity. The solution to this problem and its importance will be shown later. The ellipsoid is a reference surface that has been selected as a mathematical convenience to represent the figure of the earth.

c. Geodetic Latitude and Longitude. Points on the ellipsoid can be defined in terms of latitude and longitude. These coordinates are called geodetic latitude and longitude. These coordinates are the same as those that appear on charts and maps. There is only one value of geodetic latitude and longitude, which locate a single point to the ellipsoid.

In Figure 1-3, the geodetic latitude of point P has been formed by the angle of the semimajor axis and a perpendicular (or plumb) from point P on the edge of the ellipse. The geodetic longitude of point P has been formed by the angle between the plane of the Greenwich meridian and the meridian plane of point P.

Figure 1-3.  Geodetic Coordinates
Figure 1-3. Geodetic Coordinates

 

d. Defining the Earth's Equator. For years, scientists have discussed the possibility that the earth's equator is an ellipse rather than a circle and, therefore, that the ellipsoid is triaxial. Until recently, the study has been slowed due to insufficient data. Modern technological developments have furnished new and rapid methods for data collection, and since the launching of the first Russian sputnik, orbital data has been used to investigate the theory of ellipticity. However, it will be some time, even at today's rate of data collection, before an exact conclusion is made.

e. A Second Theory. A second, more complicated theory than triaxiality proposes that satellite orbital variations indicate additional flattening at the south pole, accompanied by a bulge of the same degree at the north pole. It is also argued that the northern middle latitudes are slightly flattened, and the southern middle latitudes are bulged in a similar amount. This new concept suggests a slightly pear-shaped earth and has been the subject of much discussion.

1-3. Geoid. In geodesy, precise computations are made by using an ellipsoid. Unfortunately, measurements made on the earth's surface are not made on a mathematical ellipsoid. The surface is called a geoid.

a. General. The geoid is the surface which the ocean waters of the earth would conform to if they were free to adjust to the forces acting on them. The ocean waters would conform to the surface under the continents if allowed to flow freely through sea-level canals. The forces acting on the oceans include the actual attraction of the earth's mass, attractions due to density differences in the earth's crust, and centrifugal force due to the earth's rotation. The component of centrifugal force opposing the attraction of gravity is greater at the equator than near the poles. Since terrain features such as mountains, valleys, and ocean islands exert gravity forces, they also affect the shape of the geoid. The geoid can also be defined as the actual shape of a surface at which the gravity potential is the same. While this surface is smoother than the topographic surface, the geoid still has bumps and hollows.

b. Characteristics. There are two very important characteristics of the geoid. First, the gravity potential in the geoid is the same everywhere, and the direction of gravity is perpendicular to the geoid. Second, whenever you use an optical instrument with level bubbles, properly adjusted, the vertical axis of the instrument should coincide with the direction of gravity and is, therefore, perpendicular to the geoid. The second factor is very important because the attraction of gravity is shown by the direction of the plumb lines.

c. Deflection of the Vertical. Since the ellipsoid is a regular surface and the geoid is irregular, the two surfaces do not coincide. However, they do intersect, forming an angle between the two surfaces. Geometry has taught us that the angle between the two surfaces is also the angle formed between the perpendicular to the ellipsoid and the geoid plumb line. This angle is called the deflection of the vertical. The word normal is sometimes used to describe the perpendicular to the ellipsoid and the geoid since a normal is a line perpendicular to the tangent at a curve. In less precise language, this is known as perpendicular to a curve (Figure 1-4).

Figure 1-4.  The Geoid and the Ellipsoid Rarely Coincide
Figure 1-4. The Geoid and the Ellipsoid Rarely Coincide

 

d. Separations. The separations between the geoid and the ellipsoid are called undulations of the geoid, geoid separations, or geoid heights. The geoid height reveals the extent to which an ellipsoid fits the geoid and thus helps to determine the bestfitting ellipsoid. For purposes of illustration, the undulations of the geoid in Figure 1-4 and other figures are highly exaggerated.

PART B - GEODETIC SURVEYING

 

1-4. General. One of the purposes of geodesy is to determine the precise position of points on the earth's surface. The techniques used to do this can be grouped into an astronomic observation, horizontal control, or vertical control by gravimetric. These techniques are described here so that you can examine the methods to join the continents and insure their proper placement on earth; establish correct boundary lines, ending old disputes; make flying safer by identifying the correct placement and elevation of mountain peaks; ensure the correct missile launch information and target locations in this country and in foreign countries; establish exact control-point locations for accurate maps; and aid in the establishment of a WGS. These techniques should also help to visualize how these measurements are used to determine the earth's size and shape.

1-5. Astronomic Observation. The position of a point can be obtained directly by observing the stars. Astronomic positioning is the oldest positioning technique. It has been used for many years by mariners and, more recently, by airmen for navigational purposes. Explorers often used the astronomic technique to locate themselves in uncharted areas. Geodesists must use astronomic positions along with other geodetic survey data to establish precise positions. As the name implies, astronomic positions are obtained directly by measuring the angles between the plumb line at the point and a star, or series of stars, and recording the precise time at which the measurements are made. After combining the data with information obtained from star catalogues, the position is computed.

a. While geodesists use elaborate and very precise techniques for determining astronomic latitude, the simplest method is to measure the angle between the Polaris and the horizon of the observer. Astronomic latitude is defined as the elevation of the Polaris above the horizon, or the angle between the perpendicular to the geoid at point P and the plane of the equator (semimajor axis). The angle of elevation of the Polaris is about equal to the astronomic latitude. The astronomic longitude shown in Figure 1-5 is the angle between the plane of the Greenwich meridian (prime meridian) and the astronomic meridian of the point.

Figure 1-5.  Astronomic Coordinates
Figure 1-5. Astronomic Coordinates

 

b. It is necessary to always reference a system of horizontal measurements with respect to the earth, with the exception of surveys with very limited scope, such as engineering plans or city surveys. To obtain this reference, make astronomic observations to obtain astronomic coordinates for points on the earth's surface. You will observe the astronomic latitude and longitude at a starting point known as the origin of the survey. You should also determine an azimuth or directional control to another point in the survey to provide the directional control needed in the survey network. The observation of the longitude and azimuth is frequently repeated in the survey to give control to the geodetic network. When combined with other geodetic measurements, astronomic observations provide a method for determining the deflection of the vertical. This can help in determining the figure of the earth. Places at which astronomic longitude and azimuth are measured are called Laplace stations.

c. When making astronomic observations with an optical instrument containing a leveling device, the vertical axis of the instrument is perpendicular to the geoid. This means that the axis coincides with the direction of the force of gravity or a plumb line at the observation site. Therefore, an astronomic observation gives a direction with respect to the geoid.

d. The normal to the ellipsoid defines geodetic latitude and longitude. Since the direction of gravity rarely coincides with the normal of the ellipsoid, astronomic coordinates do not represent positions on the ellipsoid (Figure 1-6). This difference, the deflection of the vertical, can be used to help determine the accuracy of the survey technique and the suitability of the ellipsoid for use in a particular surveyed area.

Figure 1-6.  Deflection of the Vertical
Figure 1-6. Deflection of the Vertical

 

e. Astronomic observations provide angular relationships only. They provide information on the shape of the earth, not its size. In order to determine distances between astronomic stations, the size of the earth must be determined by horizontal surveying techniques.

1-6. Horizontal Control Technique. Geodesy not only involves determining the shape of the earth; it also involves surveying--measurements on the surface of the earth. Surveys may be plane or geodetic. While plane surveys are restricted to small geographic areas and are computed as though the surface is level or plane, geodetic surveys are used over large geographic areas and require consideration not only of the curvature of the earth but also of the geoid. This is not the only difference between the two types of surveys. Instruments used in geodetic surveying are more accurate. Instrument errors are either removed or predetermined, and the procedures are more rigorous in order to minimize observation errors. The extension of horizontal control can be carried out in various ways. Basically, the procedure starts from some point or points of a known position, the distance and angles to new points are measured, and the positions of these points are computed by means of the measured data. The most common methods of establishing horizontal control are traverse, triangulation, and trilateration. Other methods include celestial techniques. Horizontal angles measured on the earth's surface can be used on the ellipsoid without any additional correction. There may be a very small difference between horizontal angles on the earth's surface and the corresponding angle on the ellipsoid, but the correction is usually smaller than your ability to measure the angle and should be ignored, except in the case of first-order surveys.

a. Traverse. A traverse begins at a position with a known azimuth to some other point, and the angles and distances along the line of survey points are measured (Figure 1-7).

Figure 1-7.  Principles of Traverse
Figure 1-7. Principles of Traverse

 

(1) Closed Traverse. A closed traverse starts and ends at the same point or at points which have known relative horizontal positions. The measurements can be adjusted by computations to minimize the effect of accidental errors made in the measurements. Mistakes (blunders) can be detected by rechecking the computations.

(a) Loop Traverse. A loop traverse forms a continuous loop enclosing an area. The computed circuit closure, or error of closure, for a loop traverse normally indicates whether a large mistake was made in the measurements. When mistakes are eliminated, the error of closure will indicate the size of the accidental errors. However, systematic errors will seldom show in the error of closure. For example, when the tape used for distance measurements is longer than its nominal length, all of the recorded lengths will be proportionally too small and will cause little or no change in the computed error of closure of the traverse.

(b) Connecting Traverse. A connecting traverse starts and ends at separate points whose relative positions have been determined by a survey of an equal or higher order accuracy. A connecting traverse of third-order accuracy, for example, may be run and adjusted between two stations whose relative positions were determined by a first-, second-, or third-order traverse or triangulation.

(2) Open Traverse. An open traverse ends at a station whose relative position is not previously known. Unlike a closed traverse, an open traverse provides no check against mistakes and large errors. An open traverse usually starts at a station determined by a closed traverse or by triangulation but may start at an assumed position. An open traverse is often used for a preliminary survey for a road or railroad. When the centerline location traverse is run, ties to the preliminary traverse form a series of closed-loop traverses. A random traverse is a special adaptation of an open traverse. It is run between two stations to determine their relative positions. Running the computed line between the two points usually closes the traverse. One example of a random traverse is the measuring of the distance between points on opposite sides of a lake. This is done by running a traverse line around the shore. In this example, the angles of the loop may be closed if a sight is determined across the lake from the final to the initial point. This is not considered a closed-loop traverse, since the distance between the last and the first point is not measured directly. If an electronic distance-measuring device is able to measure the distance, the open traverse becomes a closed traverse.

NOTE: By measuring the angles between intermediate survey points and the length of the traverse sides, you can compute not only the direction of the traverse but also the position of each control point. Traverse control also uses astronomic observations for azimuth measurements.

b. Triangulation. Triangulation is the measurement of angles of triangles. It is the most common type of geodetic survey. If you accurately measure the distance along one side of a triangle and all of the angles, you can compute the other two sides (Figure 1-8). Also, if you know the latitude and longitude of one end of the side plus the length and direction of the side, you can compute the latitude and the longitude of the other end of the side.

Figure 1-8.  Principles of Triangulation
Figure 1-8. Principles of Triangulation

 

(1) The side of the triangle that is measured is called the baseline. It should be measured very carefully using a bar, a chain, or tape, all of which should be calibrated and periodically checked by the Bureau of Standards. It is not easy to reduce the baseline to the ellipsoid because our knowledge of both the geoid and the ellipsoid is so limited. Until recently, it was impossible because the geoid heights were not known. A compromise is usually necessary, and the baseline is reduced to MSL. The error in doing this is small in the baseline itself; however, since the baseline establishes the scale of the control network, this error may propagate throughout the network. While this source of error may be small, increased knowledge of the undulations of the geoid permits further improvement in the accuracy of horizontal positioning. With comparatively new instruments, such as the tellurometer (a microwave system that employs line-of-sight conditions and is capable of measuring as far as 20 to 25 miles) and the geodimeter (a system that uses light as a carrier and is capable of measuring as far as 2 to 3 miles by day and 15 to 20 miles by night), you can measure distances much faster but not necessarily with greater accuracy than with the conventional methods.

(2) To establish an arc of triangulation between two widely separated locations, you must measure a baseline at each location, connect these measured areas by a series of adjoining triangles forming quadrilaterals, and compute the latitude and longitude for the vertex of each triangle. The vertex is then called a triangulation or geodetic-control station. The end of the baseline is often called the initial point, and the directions of the sides of the triangles are called azimuths (Figure 1-9).

Figure 1-9.  Simple Triangulation Net - Example 1
Figure 1-9. Simple Triangulation Net - Example 1

 

(3) Triangulation may be extended to cover larger areas by connecting and extending a series of arcs that form a network. The network, which forms the triangulation system, is mathematically adjusted to reduce all errors to a minimum.

c. Trilateration. Recently, electronic and light wave distance-measuring equipment has been applied to geodetic surveys in a technique known as trilateration. Trilateration is the measurement of the sides of a triangle. Each side of the triangular net is measured repeatedly to ensure precision. The angles of the triangle and geodetic positions are computed, as in triangulation (Figure 1-10). These systems also permit surveying over large water barriers, allowing the connection of islands and continents. Traditional electronic systems only measure distance.

Figure 1-10.  Simple Triangulation Net - Example 2
Figure 1-10. Simple Triangulation Net - Example 2

 

d. Celestial Techniques. Celestial triangulation methods permit the extension of long arcs across oceans and inaccessible terrain. All of these methods--the star occultation, the moon-position camera, and the observation and tracking of artificial earth satellites possess one common characteristic--observed data is not affected by the direction of the vertical at the observation point. The solar eclipse method has been discontinued due to the infrequency of total solar eclipses and the inconvenience and frequent inaccessibility of suitable observation sites located along the narrow path of the moon's shadow.

(1) The star occultation method provides information similar to that obtained through a solar eclipse from which the distance between observation points can be computed. This method is used primarily for connecting isolated islands in the ocean (Figure 1-11). Occultation may be defined as the passing of a larger celestial body in front of a star. The moon, which is used as the occulting body for geodesy, revolves around the earth about once a month and in its orbit blocks out certain stars. Using telescopes fitted with electronic observing and recording devices and a recording chronometer for precise time determination, it is possible to record the exact instant of the occultation of a star. For determining a position of a point on the earth, at least two pairs of observations are needed. A pair consists of occultation measurements at one known station and at another station whose position should be determined on the same datum as the known station. The same star must be observed on about the same point of the moon's limb at both stations. An approximate geographic position of the point, whose geodetic position has to be determined, is known for the prediction of the occultation. The observations yield a correction to the assumed position of the unknown point.

Figure 1-11.  Arc Distance Determination by Star Occultation
Figure 1-11. Arc Distance Determination by Star Occultation

 

(2) The moon-position camera method involves photographing the moon against a background of stars. The camera eliminates the problem of the great difference in the motion of the moon and the stars. Important geodetic data can be obtained from plates exposed at well-distributed stations. During the first international geophysical year (1 July 1957-31 December 1958), observations were made at several stations distributed throughout the world. The observed data is still being processed.

(3) The observation and tracking of artificial earth satellites shows the most promise for obtaining valuable geodetic data in the future. After the satellite is in orbit around the earth, it is possible to track it optically using specially constructed ballistic cameras or electronically by using the sequential collation of ranges (SECOR) system.

(a) For optical tracking, the satellite is photographed from known and unknown observation points. The satellite, which is designed specifically for optical observation, contains a light source which can be activated electronically for photographic purposes. Large satellites with no independent source of illumination can be photographed at dusk or dawn when reflected sunlight illuminates the vehicle. The smaller angular distances between the images of the satellite and the star background are measured, and these measurements are used to determine the direction of the satellite from the observation point.

(b) The SECOR system employs a series of transmitting and receiving stations on the ground which contact a specially equipped satellite as it passes within range. Command signals are transmitted from the ground to the satellite. When it receives the command signal, the satellite transmits a ranging signal back to the ground station. The distance to the satellite can thus be assured by comparing the outgoing signal with the incoming signals at the ground station. Various corrections must be made for atmospheric effects. Four practice stations are used on the ground. Three of these stations are located on a known datum, and the fourth at an unknown position (Figure 1-12). A series of simultaneous measurements are made from each ground station during each pass of the satellite. These measurements, when converted, establish the position of the satellite and the position of the unknown station. The unknown station can be located from 100 to 1,500 miles from the known stations. Although the SECOR system is still in the improvement stage, results of reduced data already indicate that it will be a first-order geodetic tool.

Figure 1-12.  SECOR Ranging of Satellite
Figure 1-12. SECOR Ranging of Satellite

 

(c) Because of the high altitudes of satellites, it is possible to triangulate across the ocean and to determine relative positions between continents using the appropriate tracking method. In addition to obtaining the geodetic position, knowledge of the exact period of the satellite's orbit gives a measure of the earth's flattening. To be useful for extensive geodetic work, a satellite must be placed in a very stable orbit so that its spatial position at any moment can be accurately predicted.

1-7. Vertical Control by Gravimetric Technique. The term applied to the operation of determining differences in elevation of points on the earth's surface is known as vertical control or geodetic leveling. The highly accurate leveling instrument used is aligned perpendicular to the geoid, and the line of levels follow the geoid's curvature. The purpose of leveling is to determine the elevation above MSL of any number of vertical control points from which the elevation of any other point in a survey can be computed.

a. The determination of the acceleration of gravity over the earth's surface provides a method of determining the shape of the earth. In using the earth's gravity field to determine the earth's shape, the acceleration of gravity is measured at or near the earth's surface.

b. The theory behind gravitation acceleration depends directly on Newton's law of universal gravitation. The story of Newton and the falling apple has led toward the law that governs the universe. Newton reasoned that the force that pulled the apple down was the same force that holds the moon in its orbit around the earth. He also reasoned that the force diminished as the distance from the earth increased. From this reasoning he arrived at his inverse square law which states that the force is inversely proportional to the square of the distance from the center of the earth. When the distance is doubled, the force of gravity decreases by the square of two or four. Newton also deduced that the intensity of the force of gravity depended on the mass of an object. The force of mutual attraction exerted by two bodies was directly proportional to the masses of the pair--the larger the mass, the stronger the attraction. From these deductions Newton arrived at the following law of universal gravitation: every particle of matter in the universe attracts every other particle with a force directly proportional to the product of the masses and inversely proportional to the square of the distance between them. In mathematical form this law can be expressed in the following equation:

 

  •  

    F is the attractive or gravitational force between two bodies of masses (m1m2), with m1 and m2 expressing grams; r representing the distance between them; and G showing the constant of gravitation. To put Newton's equation to use, it was necessary for scientists to find the exact value of G from laboratory experiments. Newton presented only a rough estimate of its value from astronomical observations.

    c. The universal gravitational constant (or G) is so named because its value is the same everywhere in the universe. An English scientist named Henry Cavendish completed the first accurate laboratory measurement of G in 1798. His device consisted of a horizontal rod with a small sphere of equal mass at each end. The dumbbell-shaped rod was suspended at the center by a sensitive twistable fiber. Large lead spheres of known mass were placed at the ends of the rod, near the small spheres, in such a way that the gravitational pull between the small and large masses caused the rod to rotate horizontally. Knowing the weights, the distances of the masses, and the torsion of the twisted fiber, Cavendish computed the value of G to be 6.754 x 10-8 or, written out, 0.00000006754 centimeter-gram-second (cgs) units. This constant is the force in dynes that is exerted between two masses of 1 gram each with centers 1 centimeter apart. Cavendish's value is very close to the latest accepted value of 6.673 x 10-8 cgs units determined in 1942 by Dr. Paul R. Heyl at the National Bureau of Standards. Dr. Heyl used a refined version of Cavendish's device.

    d. Using the following formula we can determine the acceleration (a) of mass m2 due to the attraction of mass ml by dividing F, the force of attraction, by mass m2. (In Newton's second law of motion, force is the product of mass times acceleration). Any force acting on a unit mass creates acceleration, which gives a measure of the gravitational attraction at any point on the earth's surface.

     

  •  

    e. The pull of gravity is usually expressed in terms of the acceleration of a freely falling body, expressed as the rate of increase of velocity per unit of time. A G-force of one is the force required to accelerate any freely movable body at the rate of about 32.16 feet per second per second. A G meter measures the G force in aircraft. A G is equal to approximately one thousand gals, a unit of gravity measurement named after Galileo. The gal has an acceleration of one centimeter per second per second (1 cm/sec2). The acceleration of gravity over the earth's surface ranges from approximately 983 cm/sec2 or 983 gals at the poles to 978 cm/sec2 or 978 gals at the equator. Theoretically, if you were to jump from an airplane above the equator, you would fall faster and faster, gaining speed at the rate of 978 gals (about 32 feet) every second. At the end of two seconds, you would be falling at the rate of approximately 1,956 centimeters (about 65 feet) per second. After each succeeding second, the speed increases at a rate of 978 gals per second.

    f. A smaller unit of measurement used in gravity measurements is the milligal, or one-thousandth part of a gal. It is used when dealing with variations in acceleration equal to one-millionth of one G. Modern instruments go even beyond this, measuring acceleration changes of one-billionth of a G or to one-thousandth part of a milligal.

    g. Gravity can be defined as the attraction that the earth has for every particle on its surface. The force of gravity holds all objects on the earth in place and prevents them from flying off into space as the earth rotates. Gravity is what brings back to the ground a golf ball hit into the air and makes water flow downhill. It is because of gravity that all things on earth possess weight. An average person will weigh about 1 pound more at the poles where the attraction is greater than he will weigh at the equator where the attraction is weaker. The variation of the earth's gravity, with respect to latitude, is caused by two factors--the rotation of the earth and the earth's ellipsoidal shape. The attraction of gravity increases at the poles because the centrifugal acceleration due to the earth's rotation decreases to zero and the mass attraction is greater since it is closer to the center of the earth where the mass is considered concentrated. The attraction of gravity at the equator decreases since the distance to the center of the earth's mass is greater. Additionally, the component of centrifugal force opposing gravity is greater at the equator.

    h. Additional variations in gravity can be caused by elevation, surface density, and topography. Oceans, plains, and mountains distort the surface, and the density (the amount of mass in a given volume) and elevation of these topographic features create regional differences in gravitational attraction. Furthermore, buried masses lying below the earth's crust exert additional gravitational pull on surface objects.

    i. The variations in gravity, inferred at first from surveying discrepancies and later determined by actual observations, led to the concept of isostasy. The term isostasy, meaning equal pressure, was first proposed by C. E. Dutton in a paper written in 1889.

    (1) Isostasy is a condition of approximate equilibrium in the outer part of the earth, such that the gravitational effect of masses extending above the surface of the geoid in continental areas nearly counterbalanced by a deficiency of density in the material beneath those masses, while the effect of deficiency of density in ocean waters is counterbalanced by an excess of density in the material under the oceans.

    (2) The basic principle of isostasy is that the masses of prismatic columns of the outer part of the earth, extending to some constant depth below the surface of the geoid, are proportional to the areas of their sea-level sections regardless of their surface elevations. The depth below sea level to which these hypothetical columns extend is known as the depth of isostatic compensation and is somewhere between 96.56 and 112.65 kilometers. The area of the sea-level section of a unit hypothetical column for which isostatic compensation is ordinarily complete has not been determined; it may be uniform for all parts of the earth, or it may vary with the character of the relief in the same continental region.

    (3) While isostasy is generally accepted as a proven principle, there are several theories as to the relative distribution of the matter producing this condition of equilibrium. The two principal theories are those of Pratt and Airy. The fundamental difference between the two theories is that Pratt postulated uniform depth with varying density, while Airy postulated uniform density with varying depth.

    Figure 13.  Airy's Theory of Compensation
    Figure 13. Airy's Theory of Compensation

     

    j. The theoretical value of gravity at a point on the ellipsoid depends on the size and shape of the ellipsoid and the observed value of gravity at the equator (978 gals). It also varies with the latitude of the observation point, assuming that the earth is a surface without mountains and oceans, having no variations in rock densities or in the thickness of the crust. The theoretical value of gravity represents the force of the earth's attraction due to gravitation, minus the centrifugal force due to the rotation of the earth.

    k. Since the earth is not an ellipsoid and there are variations in both the crust material and the terrain, the observed gravity of the geoid varies from point to point. Gravity observations must be made so that the distance between the geoid and the ellipsoid can be computed. This undulation of the geoid, or distance, must be observed point by point; it cannot be computed directly from other data.

    l. The difference between observed gravity and theoretical gravity at the same point is called a gravity anomaly. Gravity anomalies can be either positive or negative. They are positive in areas of mass surplus, where the observed gravity is greater than the theoretical value. In areas of mass deficiency, where the observed gravity is smaller than the theoretical value, the anomaly is negative.

    m. The physical basis of gravimetric studies lies in the fact that the gravity anomalies, the deflection of the vertical, and the undulations all result from disturbing masses. The gravity anomalies can be measured and, from these measurements, the important geodetic quantities, undulations of the geoid, and deflections of the vertical can be computed (Figure 1-14).

    Figure 1-14.  Effects of Mass Anomalies on the Geoid
    Figure 1-14. Effects of Mass Anomalies on the Geoid

     

    (1) The method for determining undulation of the geoid was developed in 1854 by a British scientist named Sir George G. Stokes. In more recent years, a Dutch scientist named Vening Meinesz developed the formula for computing the gravimetric deflection of the vertical (Figure 1-15).

    Figure 1-15.  Products of the Gravimetric Method
    Figure 1-15. Products of the Gravimetric Method

     

    (2) Computing the undulations of the geoid and deflections of the vertical requires extensive gravity observations. The areas immediately surrounding the computing point require a dense coverage of gravity observations. Detailed data must be obtained from distances out to 500 miles. A less dense network is required for the rest of the earth. The deflections and undulations computed from information obtained from these extensive observations are considered absolute values when referred to an earth-centered, referenced ellipsoid. In other words, the axis of rotation for the ellipsoid coincides with the rotation axis of the earth, and the geometrical center of the ellipsoid coincides with the earth's center of gravity (Figure 1-15).

    n. The collection of gravity observations requires measuring the gravity at or near the earth's surface. The ultimate goal is to obtain a good distribution of gravity observations over the entire surface of the earth. Since 70 percent of the earth's surface is water, this is not an easy task. Consequently, geodesists are forced to use Stokes's theorem method to determine geoid separation in areas where gravity observations have not been made.

    o. The absolute acceleration of gravity is usually measured with a pendulum apparatus. The swinging period of a pendulum is accurately timed, and from this time interval the value of gravity is computed. Pendulum measurements require lengthy observations, and the average period of swing must be determined from several thousand actual swings of the pendulum. This type of measurement requires several hours of observation, and the equipment involved is complex and cumbersome. Consequently, absolute gravity is usually measured at a limited number of reference stations called gravity base stations.

    p. Gravity measuring instruments, which use base stations for referencing, are generally called gravimeters. Since these instruments do not measure absolute gravity, the results are known as relative measurements. With a gravimeter, gravity at different places is compared with the value of gravity at a pendulum base station. In recent years, mostly geophysical-prospecting companies have developed several different types of gravimeters. Some of the instruments are compact and light and permit rapid movement from place to place. Relative gravity measurements are usually sufficient for geophysical prospecting, but these measurements must be properly connected to a gravity base station before the results can also be used for geodetic purposes.

    (1) Gravimeters are so sensitive that they respond to and register the gravitational attraction of the sun and the moon. Since the waters on earth have no rigidity, they are raised and lowered by forces of attraction known as tides. These same tidal forces exert a pull on the land surface. Evaluations on tidal effects shows that the moon's attraction is more than twice that of the sun. Although a point on the surface of the earth does not rise or fall as much as would a ship on the surface of the ocean due to tidal force, the slight movement of a point on the land surface causes small variations of gravity. The amount of variation depends upon the latitude, the time of the month, and the year. These variations are a source of error and must be computed and eliminated when obtaining readings with the gravimeter. This computation is known as the earth tide correction.

    (2) Gravity observations over ocean areas can be made from submarines. Such measurements still require a considerable length of time, and special consideration must be given to account for the motion of the measuring vessel. Several different types of underwater gravimeters have been built by oil-prospecting companies to perform gravity surveys in shallow coastal areas.

    (3) Gravity surveys have been made on many areas of the earth; however, there are still vast areas with only a few or no gravity observations. An airborne gravimeter and other new developments in gravity measuring devices should help to extend our knowledge of the earth's gravity field.

    1-8. Determining the Earth's Size and Shape. In order to establish a WGS, it is essential that the size and shape of the selected ellipsoid of revolution closely approximate the true figure of the earth. While Eratosthenes' measurement method has not been changed in principle to the present day, certain very important refinements have been made. A long arc is measured between two points on the surface of the earth. The angle, which subtends this measured arc, is determined from the difference in the latitude or the longitude of the two astronomically-observed points. The value of the ellipsoid's semimajor axis and the flattening is then computed using the appropriate mathematical formulas.

    a. If the shape of the earth was exactly that of an ellipsoid of revolution, the measurement of one arc on the surface of the earth should give its dimensions. In practice, numerous arcs from different areas of the earth are used to obtain a truer ellipsoid figure. As previously pointed out, astronomic observations are referred to the geoid. This causes errors in arc measurements, which must be eliminated by using gravity anomaly corrections and gravimetric computations. By mathematically removing the effects of the deflection of the vertical at the ends of the measured arcs, a more refined and truer ellipsoid can be determined.

    b. Measurements can be solved to find both the size and the shape of the earth. Reductions are often accomplished by the use of the flattening value obtained by some other method. This simplifies the arc problem to one in which only the size of the earth is sought.

    (1) The shape of the earth (not its size) can be obtained from gravity anomalies. Since the theoretical gravity formula depends on the assumed flattening of the earth, gravity anomalies are used to find the gravity formula which best satisfies certain assumptions about the structure of the earth's crust. The flattening that corresponds to this corrected gravity formula can be found by working backwards.

    (2) Artificial earth satellites can also provide a good means of measuring the flattening of the earth. This method will assume greater importance as tracking techniques with special geodetic satellites improve.

    c. To determine the size and the shape of an ellipsoid for use in a WGS, many methods should be used based on as large a group of observations as possible. Failure to do this would result in an ellipsoid appropriate for a small area of the earth but not necessarily an adequate reference for the entire earth.

    PART C - GEODETIC DATUMS

     

    1-9. General. The geodetic positions of points lying on the earth's surface are determined with respect to a group of specific initial quantities that form a geodetic system or datum. Since the relationship between geodetic positions remains true only so long as they are on the same geodetic datum. Positions derived from different datums are not directly comparable in computations. Consequently, the desired data, such as distance and direction, will be different. The difference will depend on the errors in the initial quantities of the datums.

    a. Since a datum can be defined as any numerical or geometrical quantity or set of such quantities, a datum is a starting point. In geodesy, the following two datums must be considered: a horizontal datum that forms the basis for the computations or horizontal control surveys in which curvature is considered and a vertical datum to reference heights.

    (1) Horizontal geodetic datum consists of a starting point and an ellipsoid on which to compute. Use the following five conditions or parameters in determining the computations: latitude, longitude, azimuth, equatorial radius, and flattening. Computations are made from the latitude and longitude of the initial point. The azimuth of a line from the initial point gives a direction with which the computations are made. A change in any one of these five quantities will change the datum; hence, the coordinates of all points on the datum would also change.

    (2) The vertical datum, to which the elevations of the points are referenced, is usually the MSL surface. However, it may be any arbitrary level surface defined by an assumed elevation for some point.

    b. Geodetic-datum orientation may be established using a single astronomical point and one astronomical azimuth, an astronomical-geodetic method, or a gravimetric method.

    (1) Single Astronomical Point and One Astronomical Azimuth. After a reference ellipsoid is determined or established, the other three parameters or factors must be defined. The simplest means is to select a first-order triangulation station located at the center of the surveyed area. At this point, the astronomic coordinates are observed and the astronomic azimuth from this point to another control station in the net is determined. In this method, it is assumed that the normal (perpendicular) to the ellipsoid coincides with the plumb line or the normal (perpendicular) to the geoid (Figure 1-16). Therefore, the observed astronomical coordinates and azimuth are adopted, without any corrections, as coordinates and azimuth on the ellipsoid. The two components are defined as zero--the deflection of the vertical and the undulation of the geoid.

    Figure 1-16.  Single Astronomic Station Datum Orientation
    Figure 1-16. Single Astronomic Station Datum Orientation

     

    (a) Reference Figure 1-16 and note that a datum oriented by a single astronomical point produces large geoid separations. Also, it is not earth-centered, and the rotational axis of the ellipsoid does not coincide with that of the earth. The inconvenience of such an orientation is that the positions derived from different datums are not directly comparable in any geodetic computation.

    (b) This type of orientation could be used locally for positions in the net, although large errors would probably be introduced as the survey is expanded because the entire net would be shifted relative to the axis of the earth.

    (2) Astronomic-Geodetic Method. When comparing the geodetic and astronomic coordinates of a point, discrepancies will normally be found between the two sets of values. The deflection of the vertical angle, formed by the intersection of the ellipsoid and geoid normals, is usually expressed in terms of north-south and east-west. The north-south component, frequently called the meridional component, is equal to the difference between geodetic and astronomic latitude. The east-west component is proportional to the difference between the geodetic and the astronomic longitude and proportional to the difference between the geodetic and the astronomic azimuth. Consequently, the east-west component can be found in two ways. From the two ways of expressing the east-west component, we derive what is known as the Laplace equation.

    (a) Since the Laplace equation is derived from certain mathematical relationships which involve the components of the deflection of the vertical along with astronomical and geodetic latitude, longitude, and azimuth, the following equations shown in Table 1-2, may be more enlightening:

    Table 1-2. Deviation of the Laplace Equation
    Table 1-2.  Deviation of the Laplace Equation

     

    (b) Refer to Table 1-2, and note that equations (1), (2), and (3) use the gravimetric method to obtain the components of the deflection of the vertical (? and ?). If the astronomical coordinates and azimuth have been observed, the geodetic coordinates can be computed. The largest computed difference in position between astronomic and geodetic observations is approximately 1,000 feet. The average difference between the computed positions is somewhere in the neighborhood of 300 feet. These differences in position look very small. However, we are looking for a precise position; consequently, the geodesist must indicate the exact pinpoint position, not an approximation. This is especially critical at the initial point of any weapons system since any deviation will influence the final location of the impact area.

    (c) The Laplace equation (5) in Table 1-2 is important because it gives the relationship between the azimuth and longitude differences without knowing the components of the deflection of the vertical. In survey networks this fundamental relationship is used as a check to determine the accuracy of the observed geodetic and astronomic data.

    (d) The astro-geodetic deflections of the vertical are only relative since the deflections of the vertical are computed with respect to a specific ellipsoid. If the ellipsoid is changed, the deflections of the vertical also change (Figure 1-17). It is necessary to assume a specific orientation of the reference ellipsoid with respect to the geoid before computing the astro-geodetic deflections. This orientation is fixed by the initial values of the datum point from which the geodetic coordinates were computed. Any change in these initial values, therefore, changes the deflection of the vertical at each point. Consequently, the astro-geodetic deflections of the vertical have the same restrictions as the geodetic positions. They are related to the geodetic datum.

    Figure 1-17.  Astro-Geodetic Deflection of the Vertical
    Figure 1-17. Astro-Geodetic Deflection of the Vertical

     

    (e) It is possible to produce a profile of the geoid with respect to the chosen reference ellipsoid if a certain number of Laplace stations are given in a geodetic net. This profile can then answer the question of whether the adopted reference ellipsoid properly represents the curvature of the earth over the area being surveyed. The profile in Figure 1-18 indicates that between 50° north and 25° north, along the 98th meridian, there is nothing more than random deviations from the referenced Clarke ellipsoid. However, at 40° south the difference between the geoid and the ellipsoid approaches 200 meters.

    Figure 1-18.  Geoid Profile of the 98th Meridian
    Figure 1-18. Geoid Profile of the 98th Meridian

     

    (f) Astro-geodetic datum orientation is obtained from the deflections of the vertical at a number of selected Laplace stations (Figure 1-19). In this orientation method, the geoid and the ellipsoid are oriented so that the sum of the squares of the deflections of the vertical at the Laplace stations is made as small as possible. One of the Laplace stations in the adjustment is arbitrarily selected as the origin. Consequently, instead of having a zero deflection as with the single-point orientation, there is a deflection of the vertical at the origin point. Through a similar process, the geoid separation at the starting point can be found. This procedure reorients the ellipsoid so that it provides the best average fit at all the Laplace stations. The use of geodetic data produced by this method is still limited to relatively small areas since the deflections of the vertical still remain relative. They are not comparable with similar deflections derived from another adjustment. As in the single astronomic method, the datum is not earth-centered and the rotational axis of the ellipsoid does not coincide with the axis of the earth.

    Figure 1-19.  Astro-Geodetic Datum Orientation
    Figure 1-19. Astro-Geodetic Datum Orientation

     

    (3) Gravimetric Method. If the relative deflections of the vertical at the initial point and the Laplace stations of a triangulation net could be replaced by absolute deflection components, the contradictions with similarly corrected adjoining surveys would be eliminated. Thus, the positions of unconnected surveys would be coordinated. The absolute deflections of the vertical and the absolute undulation of the geoid can be determined by the gravimetric method.

    (a) Use the following procedures to obtain the absolute gravimetric orientation for a triangulation net:

    Figure 1-20.  Gravimetric Datum Orientation
    Figure 1-20. Gravimetric Datum Orientation

     

    (b) Before such a gravimetric adjustment is possible, a general study of the earth's gravity field is required. A detailed study of the gravity field is required in the area of the points where the gravimetric deflection of the vertical is to be computed.

    (c) The significance of a gravity-oriented datum is the absolute nature of the coordinates obtained (See Figure 1-21). If the astronomic observations and triangulation are correct, the positions derived by this method will be absolute positions with respect to the ellipsoid chosen. Assuming that we have an ellipsoid that is a good fit to the geoid, an absolute position is given by the direction of the normal to the ellipsoid whose axis coincides with the earth's axis of rotation.

    Figure 1-21.  Astro-Gravimetric Datum Orientation
    Figure 1-21. Astro-Gravimetric Datum Orientation

     

    (d) Because the gravimetrically-oriented ellipsoid is earth-centered and aligned with the earth's axis of rotation, various gravimetrically-adjusted datums will all be earth-centered and have the minor axis of the ellipsoid coinciding with the rotational axis of the earth. This method of orientation will be especially significant when discussing the unification of various geodetic datums to a single worldwide system.

    PART D - CONNECTING HORIZONTAL DATUMS

     

    1-10. Discrepancies. When geographic coordinates of common points are derived from different datums, differences occur because of the different ellipsoids used, as well as the relative deflections of the vertical at their initial points. The latitude and longitude components of the absolute deflection at the initial points result in a parallel shift between two systems. This shift is caused because the minor axes of the reference ellipsoids do not coincide with the axis of the earth. Furthermore, deflection errors in azimuth cause a relative rotation between the two systems. Since using different ellipsoids causes a difference in the scale of horizontal control, a stretch occurs in the corresponding lines of the various geodetic nets. These discrepancies are generally larger for a datum oriented by a single astronomic point than they are for a datum oriented by the astro-geodetic method. However, even in the astro-geodetic nets, the deflections of the vertical are only relative and the system cannot be considered absolute. Consequently, it is impossible to determine the discrepancies between various systems unless direct observations can be made.

    1-11. Unconnected Geodetic Systems. Without more information, the computation of geodetic information from one datum to an unconnected datum is impossible. Regardless of how accurate the individual datum may be for computations within themselves, there is no accurate way to perform computations for distances or azimuth between unconnected geodetic systems. Since the modern military requires geodetic computations between previously unconnected datums, the major geodetic datums of the earth must be unified. The methods used to accomplish this task are the datum transformation method, the arc measuring method, and the gravimetric method.

    a. Datum Transformation Method. The datum transformation method is restricted to surveys of a limited scope. It consists of a systematic elimination of discrepancies between two overlapping triangulation networks. This is done through mathematical processes involving moving the origin, rotating and stretching networks to fit another. While this method is usually used to connect small local surveys to a national network, it can also be applied when extending control for detailed mapping purposes. However, the datum transformation method can only be used where control exists for common points in the different systems.

    b. Arc Measuring Method. The arc measuring method can establish survey ties between unconnected systems. Arcs across relatively narrow waters and land areas inconvenient for ground surveys can sometimes be obtained by electronic distance measurements. Thus, high-precision super-range navigation (HIRAN) radar trilateration provides a method for measuring distances over areas where ground stations can be established within 400 or 500 miles of each other. This offers an operational method of connecting separate geodetic datums. The HIRAN trilateration has become a standard tool, within its capacity and range, in the coordination of geodetic systems. As mentioned earlier, celestial triangulation methods also permit the establishment of arc distances over oceans and inaccessible terrain.

    c. Gravimetric Method. Components of the gravimetric method were previously discussed in this chapter. By using a single reference ellipsoid and determining the absolute deflections of the vertical and geoid separations for each initial point of all datums, the datums can be joined more accurately to a single unified absolute system.

    PART E - GEODETIC SYSTEMS

     

    1-12. General. The amount of work and time involved in establishing a single unified absolute system of geodetic datums is tremendous. For military purposes, we must know the distance and directions between widely separated points. Therefore, we must undertake this task. In this lesson, we discussed how geodetic datums are established and some methods by which the various datums can be connected. We also discussed the tools and techniques of geodesy. Now let's examine some of the problems.

    1-13. Major Datums Before World War II. Every technically advanced nation has developed its own national geodetic system or systems, depending on its technical, industrial, or military requirements. The systems were developed by the expansion and unification of smaller local systems or by new nationwide surveys to replace the outdated local ones. Neighboring countries normally did not use the same geodetic datum, since the cost of establishing a separate datum was small, and the nation's military interest was against the use of a common datum. International surveys on the same datum were restricted to the measurements of long arcs across international boundaries in order to determine the size and shape of the earth's ellipsoid. The result of this policy was that many systems developed which differed from one another remarkably, as did the map series based upon them. (An example of the many datums in Southeast Asia is illustrated in Figure 1-22.) Due to the relatively small areas covered by these national datums, military operations requiring geodetic information were restricted to fairly short distances. The development of long-range rockets and guided missiles during the war illustrated the need for more extensive geodetic information.

    Figure 1-22.  Major Datums in Southeast Asia
    Figure 1-22. Major Datums in Southeast Asia

     

    1-14. The Preferred Datums. After World War II, considerable advancement was achieved in the reduction of the different national datums and more toward large unified geodetic systems. This was achieved by readjusting existing surveys and making direct connections between the different systems. Large geodetic systems such as the North American, European, Russian, and Tokyo systems are generally limited to the continental boundaries or smaller areas. These large systems are generally called preferred datums. In military situations, which are limited to single continents, the preferred datums usually provide the necessary distance and direction information. Thus, for many types of air-to-surface or intermediate-range missiles, sufficient geodetic coverage is provided by the preferred datums.

    1-15. The Four Principal Datums. The four principal datums into which many existing major or local geodetic systems are presently united are the North American Datum of 1927, the European Datum, the Tokyo Datum, and the Indian Datum. Numerous minor surveys have been combined into these four datums to provide geodetic systems for intermediate-range weapons. The general coverage of these systems is illustrated in Figure 1-23.

    Figure 1-23.  Preferred Datums
    Figure 1-23. Preferred Datums

     

    a. The North American Datum of 1927 is used in the United States. It has its origin at Meade's Ranch, Kansas and is based on Clarke's ellipsoid of 1866.

    b. The European Datum's initial point is located in Potsdam, Germany. Numerous national systems have been joined into a large datum based upon the international ellipsoid. The National Imagery and Mapping Agency (NIMA) has connected the European and African triangulation chains and filled the gap of the African arc measurement from Cairo to Cape Town. Thus, all of Europe, the Republic of South Africa, and north Africa are molded into one system. Through common survey stations, it was also possible to convert data from the 1932 Russian Pulkova (Pulkovo) system to the European Datum. As a result, it includes triangulation as far east as the 84th meridian. Additional ties across the Middle East have permitted connection of the Indian and European Datums.

    c. The Tokyo Datum's origin in Tokyo is defined in terms of Bessel's ellipsoid. By means of triangulation ties through Korea, the Japanese Datum is connected with the Manchurian Datum. The Tokyo Datum is oriented by means of a single astro-geodetic station. Unfortunately, Tokyo is situated on a steep geoid slope, and the single station orientation results in large systematic geoid separations as the system extends from its initial point.

    d. The India Datum is accepted as the preferred datum for India and several adjacent countries in southeast Asia. It is computed on the Everest ellipsoid, with its origin at Kalianpur in central India. The Everest ellipsoid, derived in 1830, is the oldest of the ellipsoids in common use, although it is much too small. As a result of the small ellipsoid, the datum cannot be extended too far from the origin or very large geoid separations will occur. For this reason, and because the ties between local triangulation in southeast Asia are typically weak, the India datum is probably the least satisfactory of the preferred datums.

    1-16. Deficiencies. The preferred datums, though an improvement over the older national datums, have serious deficiencies. The effect of these deficiencies is that the preferred systems do not provide the geodetic information required for intercontinental-range missiles. It is true that the HIRAN North Atlantic tie permits connecting the European Datum and the North American Datum. However, this does not completely solve the problem, for both the North American and European Datums are relative (Figure 1-24). While in each case the ellipsoid chosen is an adequate fit in the area of the origin, neither provides a good fit for the entire earth. Also, the process of connecting various datums by means of intervening datums or triangulation ties allows for errors and does not always provide agreement with newly observed data. The surveys joining India to the European and the Tokyo Datums also present such a problem. Since the preferred datums are relative and the few existing connections between the preferred datums provide weak ties, it is not possible to compute geodetic distances and directions between the systems, and the requirement for long-range geodetic information is still unsolved.

    Figure 1-24.  The Preferred Datums are Relative Datums
    Figure 1-24. The Preferred Datums are Relative Datums

     

    1-17. The World Geodetic System. Because local or even preferred systems fail to provide intercontinental geodetic information, a unified world system has become essential. To establish a world system, all of the available observed data must be considered. This will determine the absolute reference system which best fits the entire earth. Once such a system is established, computed geodetic coordinates will be comparable worldwide. To develop such a system for our military purposes, all branches of the military have actively participated in a program to develop a Department of Defense (DOD) WGS.

    a. Because of its intercontinental-range missile capability, the United State Air Force (USAF) has played an active role in the development of a WGS. Due to the wide scope of the project, USAF participation has extended over a 20-year period in order to obtain sufficient data upon which to base a world system.

    b. Active participation by various USAF agencies has permitted the gathering of extensive data needed to formulate a unified WGS. An important phase of this preparatory work is the HIRAN trilateration net which spans the North Atlantic Ocean from the eastern coast of Canada to Norway. This tie permits connection of the North American and European Datums. However, since both of these datums are based on ellipsoids which provide a good fit only in the areas of their origins, connecting the two datums through the HIRAN tie overextends the usefulness of either ellipsoid. We have seen how large, systematic geoid separations can occur when a geodetic datum is extended far from its origin. Nevertheless, ties made with HIRAN will provide effective checks when the two major datums are oriented to a common absolute ellipsoid. Another significant example of HIRAN trilateration is the West Indies loop.

    c. A second major area in which preparatory work has been done in anticipation of a WGS is in the collection and analysis of gravity observations. Through an extensive program, several thousand gravity reference stations have been interconnected throughout the world. The connection of these base stations by airplane and gravimeter has permitted the reduction of numerous observations to a common usable system and, in effect, has established a world gravity system. This has permitted application to geodetic problems of data collected for oil prospecting and other geophysical purposes.

    (1) The collection of extensive gravity data permitted preparation of mean gravity anomalies for 1 x 1 and 5 x 5 degree geographical sectors that are needed for further gravimetric computations. It also permitted preparing the gravimetric geoid used in the orientation of the ellipsoid for the NIMA WGS. Much of the work in the collection and the analysis of gravity data was done by contracts with civilian universities.

    (2) An additional phase of gravity work includes computing gravity anomalies for places in which there are no observations. As stated previously, gravimetric computations require knowledge of gravity anomalies over the entire earth. Some regions of the earth are completely void of observation points, and the best substitute must be found. A theoretical anomaly can be found by considering the topography near the point and making certain applications of our knowledge of the earth's crust. Although the computations for each point are tedious and involve consideration of the entire earth, the theoretical anomaly is better than a blank observation square on a gravity anomaly map. Filling in gravity maps with theoretical anomalies is not a substitute for actual observations, and data continues to be gathered from both land and ocean gravity surveys.

    d. The reference ellipsoid used in a WGS must be based on all available information. This includes considering the data reduced from arc measurements in the eastern and western hemispheres as well as the connecting tie from the HIRAN North Atlantic arc. These arcs provide the basis for determining the ellipsoid's size. Recently, artificial earth satellites have provided a good method for determining the shape and flattening of the earth. The flattening of the earth can be obtained from a long-lived satellite placed in a high orbit. For example, the 1958 Vanguard satellite was tracked several thousand times and indicated that a flattening of 1/298 is probable. This value was suggested before from the arc measurements of Krassowsky. Krassowsky used the arc measurements as a datum element for the 1942 Russian datum. Earth satellites placed into orbit for the specific purpose of contributing geodetic data help to confirm or revise this value of the earth's flattening.

    e. Even with the best values obtainable for the size and the shape of the ellipsoid, the reference ellipsoid must still be oriented to an absolute system. As mentioned earlier in this lesson, this can be done by gravimetrically orienting the various preferred datum origins, using the same reference ellipsoid for all datums (Figure 1-25). While we can use gravity anomalies to compute the deflection of the vertical and geoid undulation for each datum, a new problem presents itself. The gravity anomalies that we have available today are defined in terms of the international ellipsoid, even though the dimensions of the WGS ellipsoid are different. As a result, the gravity formula must be revised to correspond to the new ellipsoid and must be corrected in all the gravity anomalies. With the gravity anomalies consistent with the reference ellipsoid, the gravimetric deflectors and undulations can be computed; and the major world datums can be connected in absolute orientation on a common ellipsoid. Using this procedure, the preferred datums are joined in the WGS. All that will remain to define a WGS will be the selection of an initial point for the datum, and the selection will be quite arbitrary.

    Figure 1-25.  Using the Same Reference Ellipsoid for all Datums
    Figure 1-25. Using the Same Reference Ellipsoid for all Datums

     

    f. A WGS will be established permitting the computation of distances and directions for use with intercontinental-range missiles. The effect of such a system will be more far-reaching than its application to intercontinental problems. Since the world system preserves the positional relationship of points within a local or preferred datum, the unified world system will also meet the requirements for geodetic information for short- or medium-range missiles. In this way, the air-to-ground missiles, the ground-based intermediate-range missiles, the ocean-based intermediate-range missiles, and the intercontinental-range missiles can all use the single WGS.

    1-18. The National Imagery and Mapping Agency World System. NIMA is working to formulate a world reference system. The approach used by NIMA is different from the approach of the USAF, but it was vital that the fundamental concepts of methods were consistent.

    a. The basic NIMA approach is to use the numerous arc measurements that span North and South America, Europe, and Africa. These arcs are used to determine the ellipsoid that provides the best fit for all the areas. In order to properly orient this ellipsoid with reference to the earth's axis of rotation and the center of the earth, a combined astro-geodetic deflection and gravimetric method will be used. By using numerous deflections in the western and eastern hemispheres, astro-geodetic undulations will be computed. These undulations will then be compared with absolute gravimetric undulations, and an adjustment will be made so that the difference between the astro-geodetic and gravimetric undulations is at a minimum. The end result of this method of orientation will be an absolute reference system in which all geodetic datums are unified. An important feature of this method in its dependence on gravimetric undulations based on observed gravity anomalies. The anomalies, in turn, depend on the gravity formula used. For the NIMA program, the international gravity formula and a flattening of 1/297 are used. Before these geoid undulations are used, corrections will be required for any flattening change adopted.

    b. NIMA is participating in other important programs contributing to developing a WGS. These programs, including celestial triangulation and star occultations, have been used primarily to connect isolated islands to a world datum.

    1-19. The Department of Defense World Datum. It is very probable that the world geodetic systems determined by NIMA and the USAF will not agree in every respect. While the fundamental principles involved in each approach are in harmony, the use of different groups of observed data is expected to cause minor differences in the final results. Since a unified world system is desired, the two systems obtained will be compared, and the major differences will be investigated by the DOD. However, the task does not end there. New information will be gathered and evaluated to permit further refinement of the world system. New geodetic methods, extended arc measurements, extended gravity surveys with new measuring methods, and data obtained from earth satellites will all contribute to the determination of a single world reference system that provides an increasingly close approximation to the true figure of the earth.


    GO TO:

    Lesson 1 Practice Exercise
    Table of Contents

    Downloadable Files