6.   Milling Machine Adjustments

a.   Vertical Milling Machine.

(1)   Adjustments.

(a)   Proper gib adjustment procedures must be done after 40 hours on new mills.

(b)   Each 700 and 800 series of mills have three gibs. One at the front dovetail of the table, one on the left dovetail of the saddle, and one on the left dovetail of the knee. Each gib is supplied with two lock or adjustment screws. The table gib has a lock screw on the right front of the saddle and the adjusting screw on the left front of the saddle.

(c)   The saddle gib is at the rear of the saddle on the left side, while the adjusting screw is at the front of the saddle on the left side. The knee gib lock screw is on the bottom of the knee on the left side and the adjusting screw is on the top on the left side.

(d)   To adjust the table gib, loosen the table gib lock screw several turns and tighten the adjusting screw on the opposite side of the table until the gib is pressing against the table dovetail. Tighten the lock screw. (Do not tighten the lock screw too tight as it distorts the gib.) Run the table back and forth and check the table for drag. To adjust the saddle and knee, use the same procedures as above.

(2)   Adjustments With The Dial Indicator.

(a)   When checking the gibs with a dial indicator, the following checks should be made: (Use figure 22 as reference.)

(b)   With the dial indicator mounted, as in Position 3, the table can be tested for looseness by pulling back and forth on the end of the table. Anything over 0.0015-inch is too much and requires the gibs to be adjusted, also the table should snap back to the "0" reading each time after the table is released.

(c)   To check the saddle gib, the indicator should be mounted as in Position 7 and the same tolerance should exist here.

(d)   The knee gib will be checked as shown, with the dial indicator in Position 5, by grasping the table and lifting up and pushing down. The reading of deflection here should not be more than 0.0003 of an inch.

(e)   As a final check, set the dial indicator on Position 2 and run the table to its extreme right and left positions. The indicator runout should not be more than 0.0015 of an inch.

(3)   Quill Feed Clutch. Adjustment of this clutch is as follows:

FIGURE 22.  INDICATOR POSITIONS FOR CHECKING ADJUSTMENTS.

FIGURE 22.   INDICATOR POSITIONS FOR CHECKING ADJUSTMENTS.

(a)   In the rear of the head, between the head and the adapter, is a hex nut with a 10-24 x 1/2 inch socket head cap screw, used for a lock. Unscrew this lock screw until you can rotate it freely with your fingers.

(b)   The minimum clutch tension is preset at the factory. If more tension is desired, rotate the hex nut to 180° from its present position, and relock the NO. 10-24 socket head screw.

(c)   It may also be desirable to adjust the travel of the clutch plunger:

1   This adjustment is made by means of the 1/4-20 x 3/4 socket set screw immediately behind the feed cam housing.

2   With the clutch disengaged, tighten the set screw (clockwise) while moving the quill down by means of the hand lever until a little roughness can be felt.

(4)   Troubleshooting.

NOTE

Ordinarily trouble will not manifest itself except when actually working with the machine.

(a)   Slide Ways Forking Hard Or Binding.

1   Cause - The gibs are out of adjustment, they are either too tight or too loose. This causes the gib to "wedge."

2   Remedy - Adjust the gibs.

3   Cause - There is dirt in the slide ways.

4   Remedy - Wash out slide ways with light oil.

(b)   Chatter Or Vibration When Cutting.

1   Cause - Dirt in the spindle taper, causing a bad fit between the tool holder shank and the spindle taper.

2   Remedy - Clean the spindle taper and the shank of the tool holder.

3   Cause - Faulty sha the tool holder.

4   Remedy - Replace the shank or dress off the burrs, if they are due to nicks.

5   Cause - Gibs poorly adjusted on the slide ways, or dirty.

6   Remedy - Clean and adjust the gibs as required.

7   Cause - Work improperly clamped to the table of the milling machine.

8   Remedy - Check for rocking or movement, and correct by proper clamping.

9   Cause - Improper ground cutting tool.

10   Remedy - Replace or regrind the tool.

11   Cause - Hard spot at the splice of the drive or the worm belts.

12   Remedy - Replace the belts.

13   Cause - Spindle quill worn in the quill head.

14   Remedy - Tighten the quill head lock slightly.

15   Cause - Incorrect spindle speed, table feed, or both.

16   Remedy - Ordinarily, increase the spindle speed and/or increase or decrease the feed to break up the vibration period. Experiment by using the hand feed to feed the table.

17   Cause - Drive pulleys are worn in the grooves or loose on the shafts.

18   Remedy - Replace the pulleys.

(c)   Boring or Milling Out Of Square Or At An Angle.

1   Cause - The head is not properly aligned with the table.

2   Remedy - Check the head for alignment and correct.

3   Cause - Work improperly set up; i.e., not square or flat.

4   Remedy - Check and re-align the work.

(d)   Failure To Hold The Center Distance When Locating For Boring.

1   Cause - Failure to take back-off tension on the lead screw after coming up to the dial indicator reading, causing the table to "creep'; or failure to lock up the slide ways with the same amount of tension after moving the table to a new position.

2   Remedy - Take the back-off tension off from the lead screw after coming up to the indicator reading and lock the table in position.

b.   Plain Milling Machine-knee Type.

(1)   General. The spindle bearings used in the spindle head are the taper roller type and have been properly adjusted for average conditions before leaving the factory. They should not require readjustment before the machine is to be used. If desired, the end play in the spindle bearings may be checked after a few months of operation in the following manner: Using a lead or composition hammer, gently tap the face of the spindle until all of the play is taken up towards the rear of the machine. Place a dial indicator against the face of the spindle, and then tap the spindle shaft forward from the rear. If the play exceeds 0.001 inch, adjustment may be made as follows:

CAUTION

Do not attempt to take up the spindle bearings without a thorough knowledge of the bearing adjustments and the operating conditions.

(2)   Adjustment.

(a)   Remove the rear cap from the cutter head.

(b)   Loosen the set screws in the bearing head.

(c)   Loosen or tighten the nut as necessary to secure the desired adjustment.

(d)   Tighten the set screw and reassemble the rear cap on the cutter head.

(3)   Checking Gib Adjustments.

(a)   Gib adjustments should-only be made by those who are thoroughly acquainted with the operation of the machine. In general, all of the gibs should be tight enough to eliminate any and all play, but not so tight that there will be a heavy drag on the working parts. Gibs that are too loose will result in inaccurate work; gibs that are too tight will cause severe wear and strain on the operating mechanisms.

(b)   The gibs are properly adjusted at the factory. When readjustment becomes necessary, proceed as follows: The table gib is adjusted by means of two shouldered screws located on each end of the saddle. By first loosening one and then tightening the other, the taper gib may be adjusted as needed. The saddle and knee gibs are adjusted in a similar manner.

(c)   The ram gib is adjusted by two adjusting screws. The front and the end screw are the adjusting screws. To adjust the gib, the ram stops must first be removed. These stops are located on the bottom of the ram. To remove the stops, loosen the set screws, which are located on the front and back end of the column, and turn both screws on the gib an equal amount. After proper adjustment has been accomplished, retighten the set screws in the column to hold the adjustment and then replace the ram stops.

(4)   Table Feed Screw. Backlash in the table feed screw is adjusted by an adjustable bronze feed screw nut that is located at the left hand end of the saddle. This nut is located in the saddle mechanism just above the saddle binder. To make any desired adjustment, first loosen the check nut and insert a pin in any of the many holes around the flange of the nut. Then turn the screw in either direction until the backlash is from 0.002-inch to 0.005-inch. After you have completed this adjustment, tighten the check nut.

(5)   Saddle Feed Screw. The saddle feed screw is adjusted by means of a bronze adjusting nut. This adjusting nut is located in the rear end of the bracket which is used to carry the screw, located under the saddle. To adjust the feed screw, remove the plate from the left side of the knee. Then loosen the two Allen screws that holds the bronze nut. Insert a pin into one of the holes in the circumference of the nut and turn it until the backlash is from 0.002-inch to 0.005-inch. After the correct adjustment has been made, tighten the two Allen screws and replace the cover plate.